hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
Hi, I want to create a partition setup (for the nRF5340) which I can use with future versions of the nRF Connect SDK, which means future versions of mcuboot and b0n. If we...
Hi,
I am testing two advertising sets on nrf sdk v2.6.0. Legacy advertising and long range. I tried to modify https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/samples...
Hello,
as part of my tries to use xip on nrf52840, I found that using the entire program on the external flash is impossible due to Errata 216 .
I check the FICR for my...
Hello,
I am needing to use two separate SPI masters, but I'm running out of pins. Are all of the pins compatible with SPI or are there some I should avoid. I'm thinking...
Hi all,
I have an application that is pretty simple. One master that needs to stream small payloads (sub 32 byte) to a receiving device. The payload is a fixed size and...
Question: nRF9161 Getting the high accuracy oscillator (HFXO) outside and sync with other nrf chips?
Basically I want to get the Clock Signal outside on a Pin, is it an...
We have 1 central device and 4 peripheral devices in which one of the peripheral is mobile device if we connect both mobile and other peripheral devices(nrf52840) the central...
I am testing an nRF9160 devkit with a TMP117 I2C sensor. My current goal is to read values from its registers.
My current code uses the function i2c_reg_read_byte to read...
Hi,
I've just received a nRF52840 DK and I'm trying to build and flash the blinky sample on it but the build failed continuously.
I also tried with other sample like the...
I want to convert raw hex bytes to utf8 format. The nRF5 SDK supported this with help of ble_srv_ascii_to_utf8() api. Is there something similar api available with nRF Connect...
Hello,
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0 ]
I am planning to set up the system as...
Good night,
I am doing the course "nRF Connect SDK Fundamentals" to learn about Zephir integration with nRF52840.
I am developing a RTOS solution based on the RAKWireless...
Hi,
I have an application that each 30 minutes connects to AWS, sends some data and then disconnects and goes to sleep. I have based my aplication on the asset_tracker...
I am trying to use the nrf5340 audio DK for the first time using one of the sample blink codes. I keep getting an error when first creating an application by copying the sample...
Hi everyone,
I'm a bit lost with the nordic documentation. Here : https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/applications/serial_lte_modem/doc/MQTT_AT_commands...