In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Hi,
In my project, I use SPIM4 to access sd card . It is worked well. Then ,I optimizing power of sd card. The power of my sd card is controlled by LDO.The LDO is enabled...
I'm browsing the Application Event Manager code, and I'm wondering:
I see that struct event_type has (effectively) an array of struct event_subscriber , bounded by pointers...
Hi,
I am using SDK 2.0.0.
I have two problems in this function.
Lets take Vt value as 1420, in one instance.
1. RT2 is calculated as 5076.14. This is incorrect....
I have been trying to implement the IPC code given in to send an event from the network core to the application core. I added CONFIG_NRFX_IPC=y the prj.conf for both cores...
I am working with a board one of my peers designed that hopes to use an NRF9160 for cellular communication (and GPS as well but that's neither here nor there). When setting...
Dear all,
I have pca10059 nrf52480 dongle which I accidentally erased and I could not upload any elf file to run moreover it was not blinking red anymore, no presence in...
my master is outputting all the right signals on the SPI lines. The slave though, although it appears ot recognize the CSN pin and runs the spi_tranceieve function. It does...
Hi
I'm trying to send and receive data with MQTT.
I tried uploading asset trackerV2 bin file and it works fine with nrf cloud.
now I want to use the sample "MQTT_simple...
Hi there,
We have recently acquired some new nrf5340DK's and we suddenly noted that the SYSTEM ON LOW POWER current increased from about 5 uA to about 25 uA.
Attached...
Hello guys
We have a problem with the SPI bus driver on the nRF9160 MCU. In our project, we use SPI1 and SPI3 instances.
When I send a package in some of these SPI busses...
Hello, after the excellent Nordic Techtour yesterday, I decided to try and implement the nordic distance toolbox.
However, my available hardware (52DK) is not supported...
Hi!
I'm developing a project on visual studio with ncs sdk V1.8.0. For a while, I was able to debug my project with no problem. But out of the blue, I'm no longer able to...
Hello,
While working on optimizing battery life, i noticed something strange.. This particular code actually does almost nothing other than setting low power mode (instead...
I'm trying to view core dumps on Memfault's web app, and having trouble doing so. I can't even see hard faults being logged even though I know they're occurring (forcing stack...
in the nRF52840, SPIM3 allows for high speed >4MHz communication. But I cannot see if there are dedicated pins specific to this mode, or can i map any pin to the SPIM3 high...
