Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hi,
I am using BL653dvk, which has nRF52833 as soc. I am working on DFU-OTA example by following this link.
https://devzone.nordicsemi.com/f/nordic-q-a/83402/ncs1-8-0...
I tried to build hci_spi example application for nrf5340...
identifier "__device_dts_ord___BUS_ORD" is undefined
identifier "__device_dts_ord___P_irq_gpios_IDX_0_PH_ORD...
While migrating my project to use the new pinctrl mechanism in I ran into an issue where the I2C communication on some busses was not working. Further investigation revealed...
Nordic Connect SDK 2.0.0 moved to the use pin control interface, also for I2C.
When I tried to port some of my application I noticed a possible regression.
As a basis...
According the BLE specification, the software and firmware revision strings are mandatory. I would like to set put information about the softdevice version in the firmware...
I'm trying to make a one-shot mqtt function. The process is below
- connect - publish - disconnect
Then I coded like below. I show only the core code.
Do I have to...
Hi,
I want to get a sample that supports both BLE OTA and NUS functions, so I find the following two samples as reference and merge them together.
...\zephyr\samples\subsys...
Nordic BLE Mesh transmission is transmitted through the Publish address bound to the model in the Instance, so that subscribers can receive packets.
As shown in the figure...
Project: Variation of Nordic ble_peripheral project
SDK: 15.1, Softdevice : 132 rev 6.1
How do you change the BLE packet length? I have a project where I defined a characteristic...
I am using the example zephyr basic button which gives output when the button is pressed.
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.9.1/zephyr/samples/basic...
Hi,
I have installed the nRF Connect SDK v2.0.0 with Visual Studio and can now successfully, build, flash and run the nrf9160 at_client sample application. But when I try...
we currently have a product which use nrf52832 as processor using SD132 for BLE capability with DFU capability
we want to build a sister product with nrf552810 with no SD...
HI,
We are looking to multiplex a few I/O on the NRF52840 to save pin count on a header. If D+ or D- get driven when VBUS is unpowered, will that damage the NRF52840? Or...
Hi there,
I think that I am seeing the repercussions of errata item 136 in my application. I abruptly turn on/off power several times to my board, and every once in a while...
Hi,
On my bl653_dvk board, I am running the ADC example. It functions properly. I have a few questions about this:
1. How to determine which clock is being used by the...
