Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hi,
Legacy SDK bootloader and dfu preparation workflow had the following option:
hw_option allowed for checks, whether supplied firmware matches given hardware. So firmware...
Using nrf5340 audio DK & ncs v2.60
I modify this function to print this information when the number of packages reaches 100.
\
Part of the result:
120*100*8/(...
Hi, I'm trying to implement timer synchronization on one central and multiple peripherals, I'm using nRF52840 and NCS v2.8.0. I've seen the example conn_time_sync which uses...
Hi,
I am using download client for downloading a file.
I am using download_client_get and get fragments in callback.
When the file requested is short in the callback...
Hello Nordic Team,
I'm developing a project with two nRF52/nRF54 microcontrollers where I need: - 1st microcontroller as BLE peripheral receiving mobile app data (nRF connect...
I'm migrating code from ncs 2.7 to 2.9.
I am using CONFIG_BT_EXT_ADV and scan timeout callback - such timeout requires CONFIG_BT_EXT_ADV:
It was working fine. Now it's...
Hi,
I follow the custom board exercise steps with mynRF52840 DK and when I reach step 8.1 , in the deviceTree visual editor, I notice that the GPIO0/1/TE options under ...
Hi, I recently updated from NCS 2.6.0 to NCS 2.9.0 which had lots of changes. I believe I ported from child_image to sysbuild with success, as my main application on app core...
Nordic has changed the API of nrfx nrf_modem_dect_phy from SDK 2.7 to SDK v2.9.
In struct nrf_modem_dect_phy_callbacks there is an additional callback member stf_cover_seq_control...
Hi Team,
As mentioned in the datasheet of nRF9151, Imcuoff0 mode (MCU off, modem off, wake on GPIO and reset) consumes around 1.4 uA over VDD power supply then what is the...
Hi ,
IDE: SES
NCS version: 1.9.1
I install the development enviroment following this article. 开发你的第一个nRF Connect SDK(NCS)/Zephyr应用程序 - iini - 博客园 (cnblogs.com)
I use...
Hello,
I am trying to find a solution how to use wifi and ble on thingy91x and manage the coexistence between them, I have found a sample Wi-Fi: Bluetooth LE coexistence...
I am trying to implement the following: I have a mesh node built using the Sensor Server example for publishing temperature data. I want one relay node to transmit the temperature...
Hello All I'm new to the forum so please be gentle! I hope this is ok to ask: I'm in the early stages of planning a project that I hope will be suited to a DECT NR+ platform...
