I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
Hi,
I currently developing my own NRF9160 board Based on NRF9160 DK schematics. My question is, can we remove all passive antenna circuit with all matching network and...
I am using the Fanstel BT840 module with an Epson FC-135 32.7680KA-AC3 crystal and 12pF NPO caps. It functions well in indoor conditions but the LF oscillator stops if placed...
Hi,
I am following this tutorial ( https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.0.0%2Fble_sdk_app_blinky.html ) to learn how to...
Hello,
I have nrf51822 based Board,
and I need to make Android app for scan and modify Beacon's data.
I found "nRF Beacon" App's source code in GitHub,
and I try...
Hi,
I have seen that there are three most useful topology for mesh : Bluetooth mesh, zigbee and Thread
What parameter should we have to take in consider when selecting...
I'm trying to use a timer with S130, but it doesn't seem to tick:
void timer_event_handler(nrf_timer_event_t event_type, void * p_context) {
NRF_LOG_INFO("Timer 1 interrupt...
Hi,
I recently started experimenting with nRF52840 eval-kits and a nRF52840 dongle using the generic onoff client and server. I used my phone and the nRF Mesh App to offload...
I learning NRF52832 beacon using SDK15.2 i tested code ble_app_beacon code in non connectable beacon mode its working fine. how can i change this code like connectable beacon...
Hey, I would like to add BLE mesh functionality to my existing project which is based on the firmware v2.2.0 https://github.com/NordicSemiconductor/Nordic-Thingy52-FW . I...
I'm planning to connect The nRF52840 MCU GPIO in series to a 1.8V 20mA LED and a Resistor then to ground.
Would the current from the MCU be sufficient to power the LED ...
Hi,
Here is my issue, I don't enter in bootloader by using the buttonless DFU characteristic. Here below I expose my action and what it happens. Thank you in advance for...
Hi everybody,
This is my set-up : nRF5_SDK_13.0.0_04a0bfd, Eclipse 2019 03 IDE, NRF52832_xxAA, s132_nrf52_4.0.2_softdevice, windows 64 bits, NRFConnect 4.22.3, JLINK RTT...
Hello,
we have to integrate the nrf9160 into our own company internal build system / eco-system (freeRTOS based), e.g. not using the complete nordic sdk. As a starting point...
hello,
Now i want to adv only with 37 channel, i want to use SDK15.0.
i add m_adv_params.channel_mask[x] in advertising_init() as:
static void advertising_init(void...
