Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello.
I'm working for a Zigbee networking project.I chose nRF52840 as the coordinator.The coordinator acts as a gateway to communicate with Zigbee 3.0 devices on the market...
Hi. I am trying to add FDS to my application where I used freertos and ble. I tried few things always ending with hardfault, one time it was from Freertos scheduler and the...
Hi
I have a problem changing the max_rx_octets and max_tx_octets parameters with the sd_ble_gap_data_length_update function. On request from the app the size is attempted...
HI, we have updated our DK firmware (mfwnb1nrf9160030123prealpha) for nb-iot but after inserting the Vodafone (Ireland) V-Sim we only have a flashing LED 3.
nRF connect...
Hi all
Chapter 26.1.1 of the nRF51 series reference manual v3.0 states that the pins used by the SPI master have to be configured in the GPIO registers according to table...
Hi, I am interested to learn THINGY 52 working
I want to know how does the Thingy52 works?. any tutorial to explain the function of THINGY52
How to delete the boot loader...
Hi
The example in SDK15.2 for 52840 as a Beacon is not long range (I think).
Is there another example that will enable long range and also to enable connection?
While...
Hello,
I'm use laird BL651 with nRF52810 module. I flash the chip with beacon program from zephyr samples. I use Segger Studio.
The chip is discovered by smartphone (with...
Hi,
is it possible to scan 10000 beacon having adv interval of 10 seconds. is their any maths or formul we can do ?
i have set nrf52 to scan continuesly,
Hi,
There have 4 PWM sample code (low_power_pwm, pwm_driver, pwm_library and pwr_mgmt) in SDK 15.2.
I my use case is "Control 6 PWM output with different duty-cycle and...
We have written an application based on SDK V12.2.0 using S132_V3.1.0 for the nRF52832 and have been dealing with an issue where the module constantly enters a hardfault....
Let's suppose the PC (a laptop) goes to standby while a BLE connection is established with a Nordic dongle using pc-ble-driver v4.0.0:
- With SD API V2, status handler is...
Hi
I downloaded and successfully build and ran the asset tracker sample on the nRF9160 DK using segger embedded studio. In a first step I want to reroute the debug UART...
Hi there,
I have a project where I am using the NRFX I2S Driver. I am using SDK 15.3.0 and SES 14.2.
In my sdk_config.h, I have the legacy I2S driver disabled and the...
Hi all,
I read from previous answered question found that version6.1.0 with s15.2 supported only S=8 encoding transmision when LE_CODED_PHY is chosen.
Does nRF52840 with...
