Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
I have been successfully using the Peripheral UART example on a 5340DK board. I tried rebuilding for the 7002DK, and am getting runtime errors. The UART initializes, but the...
Hi all, I am trying to understand the different Access Port Protection mechanisms on the nRF52840. From several tickets, own experiments and from the data sheet I was able...
Code runs fine in v2.53 but when running in v2.6, we get a kernel panic at the exit of a delayable workqueue function.
Tracing the code and line number, it dies in Zephyr...
I made a device based on the nRF52832 and am developing an app to control it. The control works great, I can send and receive BLE signals with react-native-ble-manager. I...
Hello,
I am working on creating a custom board using BLE BE33 module based on the nrf5340dk_nrf5340 board.
Previously i tried the peripheral uart and central uart to transfer...
The drivers in the paths
/opt/nordic/ncs/v2.6.1/nrf/drivers/sensor
and
/opt/nordic/ncs/v2.6.1/zephyr/drivers/sensor
are different.
I'm using NRF52 and VSCode with...
With nRF as advertising peripheral, is it possible to measure RSSI of active scanners' SCAN_REQ packets. `bt_le_ext_adv_cb` has a `scanned` callback, but it looks like it...
Hello,
I try to implement little fs to my external flash memory. I am using nrf52832 board and my memory is IS25LP128.
Without the connection of the memory the nrf board...
I wanted to change the Peripheral UART program in the nrf samples to the host_only version, and I made some attempts. I added the following code to the prj.conf file:
...
I am trying to get hello world to work:
/*
* Copyright (c) 2012-2014 Wind River Systems, Inc.
*
* SPDX-License-Identifier: Apache-2.0
*/
#include <stdio.h...
Hi,
Im just starting to use the nRF9160 with the SLM application flashed. All the samples and articles I found were always using stuff like the LTE link control library...
Hello,
when I play around with the matter template example, I always get a thread child device. How to get a full thread device with routing etc?
Thanks, Edi
Hi,
I'm using a Azure IoT Hub to connect some devices to the cloud and then uses the Direct Method to send messages to the devices. I can send messages and receive the response...
Hello,
I want to work on NRF52832 using VL53L3CX. When I look at the SDK, there are source files for VL53L0X and VL53L1X. I have previously worked on VL53L0X using this...
