Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi,
can i savely process / parse the incoming scan data INSIDE the scan callback or should i deferr / forward it somehow to the main thread for performance reasons?
Or...
Hello,
we are working on a BLE + Thread project, and it is currently based on NCS 2.6. We would like to update the SDK to a current one, and I see that there is a preview...
Hi,
I have added " config HW_STACK_PROTECTION" in KConfig file of the board.
Is there a way I can check during runtime if the Stack Protection is enabled? Is there any...
Hello
I am building a hardware that requires to use the nRF9160 together with the nRF52840, in order to add the 2.4GHz radio support to the system and also to be able to...
Hi,
Is it possible to run nRF5 SDK for Mesh examples on nRF Connect SDK for Bluetooth Mesh using nRF52840 Dev Board?
Examples are available on this github page.
https...
Hello,
I am trying to make GPIO P0.07 to high, in my nrf5340 Audio DK. Externally I am connecting an LED between P0.07 and GND. But it not showing any voltage between them...
I have the nRF Hw v1, and it seems like I did something wrong with a Fw:
nRF is recognizable by a computer as the COM3/4/5 device:
And it is accessible with the nRF...
Hi,
I want to know how to find the pack of nRF5 SDK.
Because the previous URL has expired. (http://developer.nordicsemi.com/nRF51_SDK/pieces/nRF_DeviceFamilyPack/ )
Hi Nordic
In the documentation of Zigbee sample of nrf Connect SDK, it said:
>>
Support for Zigbee R22 has been deprecated in nRF Connect SDK v2.8.0 and it will be...
Hi Community
Greetings, I bought nrf9151 DK module looking at the features, power consumption & size but the fact that NB IOT has a communication rate of 15mins once in...
Greetings,
We have a PCB with nrf52 and nrf91 on it.
We have nrf9160 firmware with MCUBoot. The chip boots into mcuboot dfu mode when a certain pin is set to high during...
Hi all,
We are running v2.4.0 SLM in nRF-9160 as pure modem, communicating with our external MCU. And we need to send a MODBUS-TCP write request command about each 10 seconds...
Hello.
Thank you very much for releasing nRF Connect SDK v3.0.0-preview1.
I quickly tried the sample program, and while the build was successful, I encountered an issue...
Hi everybody
I'm trying to modify the Zephyr serial LTE modem example so that CMUX can be controlled using another communication interface, specifically I'm imagining...
Our application is designed to remain connected to the network - sending data every 10 minutes or so. We've customised the asset tracker v2 application, as this provides the...
