Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
Hello,
i'm working with my own board with the SD V6.0 and nrf51822 chip id QFAAG0. Already works fine.
Now i switch to the new SD V8.0. The SD V8.0 is programming with...
Hi everyone,
I'm working on the nrf51822 chip and using S110 stack of SDK 6.1. Everything is fine for IPhone5s. The proximity example is running on the nrf51822 device...
Hello,
I have an application that runs on a 9160 which uses mbedtls (via TFM) to connect to an AWS server. The application is using a CA that you folks have given me in...
Is there a way to change a build configuration after it was created?
I want to change the kconfig fragments it is calling, but I was no able too. I have to delete and create...
I am trying to test TLS communication between TCP server and client so, how I should generate the certificates and how to provision them in TCP server?
Can I use OpenSSL...
Hi, I am using nrf52832 development kit. MCU is waking up with two buttons and I put MCU to system off mode after successful data exchange or timeout. Init settings are like...
Hi,
I am configuring a button and an ISR to handle the events, but the interrupt is not called only when there is a transition.
Is there any other configuration needed...
During the End Of Line test of one of our device, based on nRF52832, we write the serial number of the device in some non volatile registers, specifically CUSTOMER[8] and...
Hello,
We are using the nRF52810-QCAA(QFN32) in a Beacon application. We have seen serious degradation in Radio performance while using the DC/DC vs. the LDO. More than...
Hi Forum,
i've ran into a problem with configure the nrf24l01. I've disabled all ShockBurst functionality (EN_AA = 0). When putting TX Payload into the Fifo the TX_EMPTY...
Hi~
We are going to use the MAC address and UUID as what we have.
I am trying to save the MAC address and UUID through UART, so I don't know what to do.
Currently the...
Hello,
I am trying to make a code running the Ble stack adn the FreeRtos one, i started from the project ble_app_hrs_freertos_pca10040_s132, i've just removed some things...
Hi.
Newbie stuck at installing IDE.
Trying to follow the automatic installation developer.nordicsemi.com/.../gs_assistant.html
Installed nRF Connect for Desktop v3.8...
Hi,
we have nrf52933 custom hardware.
we are flashing application through j-link.
but after every flashing , I need to hard reset the board in order to run the function...
Dear Nordic，
We developed a product based on the nRF52833 chip, with an external antenna, 3dBi gain. Set transmission parameters 100mS interval and 4dBm transmission power...
I have nrf52840 dongle will like to treat it as central. (like gateway) And sensor node is unknow ble, and adress type is Resolvable Private Address. If know the characteristics...
Using the « nrf_modem_at_cmd_async » function triggered an HARD_FAULT error if it is the first function used in the code before another function of the AT interface of the...
