Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hi ,
I need to store strings in flash and came across the NVS. I referred to the example in samples/subsys/nvs and was able to do the nvs operation.
The following are...
Hey, so I was under the belief that the maximum size of data one can include in a BLE packet is 20 bytes (23 bytes total, 3 bytes overhead, so 20 total for custom data). With...
Hello! I have been working on bluetooth for some time and I just worked with connectable advertising until now. This time I am trying to add a beacon functionality too. The...
Hello,
I am developing a BLE and IEEE 802.1.4 multiprotocol device. I implemented a parser to change some settings of the device. T he configuration is updated with this...
Hi,
I'm trying to implement a SPI Communication between Arduino UNO and PCA10056 DK. PCA10056 DK run as a SPI slave.. Arduino uno run as a SPI Master.
The problem is...
I'm using SDK 15.3.0 and SoftDevice 6.1.1 running on an nRF52832.
The iOS application works correctly when it is running in the foreground. It is able to connect and bond...
Hi,
I am trying to develop an application for Thingy:91, which would allow me getting data from BLE and sending it to the cloud with LTE. I am working on NCS 1.3.0.
Of...
I just tested with the example project, "ble_app_uart" using SDK, "nRF5SDK17009d13099.zip" on nRF52DK (labelled with PCA10040 1.2.4 2018.23) board on Segger embedded studio...
Hi ,
i am trying to interface a WINBOND W25Q64JV flash module with NRF52,i can able to read device id,status register success fully.
i wrote the data in particular address...
Hi,
I'm using nRF52840 DK as a central. Our project is based on ble_app_uart_c example. There is filter for UUID only during scan.
I noticed, that for conection establishing...
I'm using the nrfjprog command "nrfjprog -f nrf52 --reset". This sometimes causes my custom board to hang. I dont think it is able to boot at all, I do not see any uart output...
I would like to ask Nordic to create an example of an Android background service that can detect a device advertising.
Android imposes background execution limits which...
I am using nRF52840, SDK 16 + s140 with segger embedded studio.
I have already added NUS service to my application by taking reference to ble_app_uart example. I want to...
