Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
I am working with a ublox NINA-B1 based board. NINA-B1 uses the nRF52832. IDE is Segger. I followed the ublox instructions to create a custom board matching NINA based on...
What are the steps to be carried out for setting mesh network
I have flashed client hex file in one nRF52840 dongle and server hex file on other dongle. The example I am...
Hi!
I may have asked about this earlier in a lengthy question:
https://devzone.nordicsemi.com/f/nordic-q-a/35576/low-power-remote-control
But I'd like to be sure about...
(note - my core problem is that I'm trying to compile a file that's larger than 32KB, so I can't use uVision - if there is an easier way to circumvent this then I don't really...
I inherited a Nordic Semi firmware project. It was developed using s132_nrf52_4.0.2softdevice.hex and SDK 13.1.0.
How can I download these versions? I would like to start...
I installed the nRF5_SDK_15.1.0 compiled and ran the ble_app_att_mtu-throughput example.
The first run was using the default settings all went as expected. For the second...
Hello Nordic team,
I am working on ble_peripheral example. Initially application binary file size is 100 KB but after adding support of FDS application size increased to...
Hello,
I have read through all the posts I can find on this subject, but none has solved my problem.
- nRF5_SDK_15.1.0
- Example: Segger Embedded Studio Project: twi_master_with_twis_slave_pca10040...
I want to fully understand the use of RTOS in conjunction with the stack. As an example, I took an example ble_app_hrs_freertos (SDK v15.0).
Add a service, for example...
I need to count the pluse number use 51822, the frequency about this pluse is about 0.01Hz to 1Hz and is not fixed, I know use Time1 can achieve this funtion, but the problem...
I wriing softdevice ,aplication and bootloader by nrfprog tool.
But,the device works with the bootloader, not the application.
After writing, it is reset and flag is set...
Hi
I am using fatfs of nRF5_SDK_15.0.0_a53641a. Iam writing a program with keil.
I am trying to save data using SD card now.
By using fatfs example it was possible...
Hello all,
I wanna ask smth related to the use of the nRF52 as a HID keyboard (USB host).
I have already played around with the SDK example ble_app_hids_keyboard and tried...
Hi,
I'm developing a product with the NRF52832.
I have one Blue LED (APA2107LVBC) which is driven directly by a GPIO as shown below :
With a typical Vf of 2.65V, the...
