Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hi,
I was wondering, what is the professional, assembly line ready procedure to program the IMEI on an nrf9161?
So far, I've only found rajeev's post in this discussion...
Hello,
I am using a Raytac MDBT50Q (nRF52840) on a custom board , and I am trying to blink an LED, but it is not working.
"I need urgent help as this is blocking my...
We can get BLE address in adv report: How to get mac address of nearby ble devices? - Nordic Q&A - Nordic DevZone - Nordic DevZone
At that moment, peripheral not connected...
I have download this .zip from the Nordic site. I am a beginning coder and I am using AI to help assist me on my project and learning C code. I seem to unzip the file correctly...
Hi, I am trying to understand periodic advertising and some basic questions:
I am using periodic_adv example from the NCS.
I see teo ADV data defined in the file as...
NCS 2.7
NRF52840
SPIM3 at 32 MHz.
I have CONFIG_NRF52_ANOMALY_198_WORKAROUND=y and have confirmed the workaround is being activated by setting breakpoints in my code...
Dear,
I need to generate a pulse signal on one IO following this pattern: HIGH for 12us ; LOW for 106us ; and so on...
I tried to use TIMER0 with NRF_TIMER_EVENT_COMPARE0...
Howdy,
I am using an nRF52840 to perform BLE communication. For this communication I am using extended advertising to perform most of my data transmission. Thing is though...
Hello, i have a device supporting DFU OTA i'd like to create a small tool for flashing firmware from the computer to the device. I've set thr device to DFU mode. Is it possible...
I just got a PPK2. I was able to use it perfectly with Power Profiler. Great tool! Today I wanted to learn more about nRF Connect other applications. (Actually I was looking...
Hi there, I'm having so much trouble trying to get this two nRF9161 DK to communicate using SPI, being one Master and the other one Slave. I'm using the spi3 driver for SPI...
We had three nRF52840DK boards (PCA10056) for several years for use in development. Then one died (or to be fair, I killed it), so we got two more that turned out to be newer...
While using nRF Connect, I encountered an error when attempting to enter Debug mode with RTT active. Here are my J-Link specifications and log details:
When I have...
Hi folks,
I am using zephyr sdk version 2.7.0 with a custom board that integrates a nrf52832, an ens210 sensor for temperature and humidity and lis3dh sensor for accelerations...
