Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
Hello,
i'm working with my own board with the SD V6.0 and nrf51822 chip id QFAAG0. Already works fine.
Now i switch to the new SD V8.0. The SD V8.0 is programming with...
I am trying to find out if I can synchronize the timeslot to a specific time in relation to the start / end of a connection interval. I would also be fine with getting the...
Hello!
I'm developing DFU functions for my custom board.
I have some questions about DFU and Bootloader.
My development environment is below.
nrf52833
SDK 17.0...
Hi,
I am trying to communicate with nRF9160, which is flashed with Nordic SLM application.
I am not able to set the HWFC with UART0/UART2 using menuconfig in Segger...
"Failed to upgrade target. Error is: Lost connection in the middle of the transfer"
I am doing a mesh serial DFU with DFU quick start guide .
I have gotten all the way...
Hello everyone,
I want to be able to set a timer in my project. With this timer i want to be able to make my current comsumption evaluation easier.
I am using the nrf9160...
Cannot update modem (nrf9160) with "nrf connect 3.8.0"
Modem DFU failed with error: no matching trait found
no matching trait found
Installing older versions eg...
The datasheet tells me that the default source of the low frequency clock (LFCLK) is the 32.768 kHz RC oscillator (LFRC). so I took the crystal oscillator off my PCB, but...
After updating NRF Connect v3.9.0 to eliminate the recently documented JSON + connectivity errors with nrf Programmer and Power Profiler, my bash scripts utilizing nrfprog...
Hi，
1. Please provide me with an example of BMA280
2. The SDK: replication v1.7.1
3.IC:nRF9160
4. I tried to change the BME280 driver to BMA280 driver, but the following...
I am working on project in which i want to read data from sd card and send it to mobile through BLE , I am using ble_nus_send to send data but when i decrease the delay then...
Hello,
Using sd_ble_gap_adv_set_configure() with ble_gap_adv_params_t I observe that the actual time when the BLE_GAP_EVT_ADV_SET_TERMINATED event is raised is earlier to...
Hi All,
Likely because I am still quite new to this, but I have started with MQTT simple example and whenever I do use GuiConfig to make mods, it saves them to
proj/build...
The disccussion here
https://devzone.nordicsemi.com/f/nordic-q-a/24592/my-nrf52-nrf51-dk-kit-doesn-t-work
has been closed.
I followed step 4 and it took a few tries...
Hi,
I use a Segger JLink EDU (the big version, not the mini) to flash some custom boards. This used to work fine until I upgraded nRF Connect and got Programmer v2.0.
...
