SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
We are working on a project, with a working secure buttonless bootloader that works flawlessly. However I recently made it with bonds, and it works with all of the devices...
I'm experimenting with the Bluetooth Throughput sample in NCS v2.6.1. As I increase the distances between devices, I see strange gaps in the transmission from the Central...
Hello, when testing the BLE sniffer with an nRF52840 dongle (utilizing the most recent official sniffer firmware), I configured Wireshark to capture the coded PHY. After initiating...
Hi,
We are working on integrating nRF-Mesh-Library (iOS and Android) sdk into our app for mesh networking, it should support identifynode, provision, add app key and add...
I found a similar thread, but it did not solve the problem. When CDC-ACM is enabled in Device Tree, the dfu-util application cannot find the USB port. The Bootloader started...
Hi everyone
I am using nrf52840 costume board. and using NUS ( Nordic Uart Service ) as the basic start sample.
My desire:
1. UART0 and UART1 work in async mode with...
If I enter the prj.conf settings according to the lesson text then the firmware crashes with different provisioning functions from the smartphone app such as forgetting a...
It's looking more and more like a lot of my problems relate to a weak cell signal. Is the RF front end on the devkit known to be inferior to a normal cellphone? My personal...
Hello, I have connected a LR1110 module to a nrf52 (PCA10040) development kit using Arduino connectors. Anybody written a simple application regarding the interfaces?
It...
When I apply an Extra CMake build argument when creating a build configuration, it only takes effect on the first build, but none after that.
For example, I have added this...
I have a system with nrf5340 with a Central and various Peripherals with different Characteristics. The Central has all the Characteristics, therefore with different UUIDs...
Hello!
I have been trying to connect to T-Mobile's NB-IoT network using a NRF9160DK with a Twilio Narrowband sim, but have been unsuccessful so far. I have been able to...
Hello,
I am using nRFCloud with nRF9160 custom board sending data via CoAP.
I have a single firmware on my board, that will behave differently depending on the value of...
Hi,
On my machine, I installed the SDK through VSCode with the extension pack. All runs smoothly and I can build from vscode and from command line with :
My C:\ncs...
I used multiple software timers, all of which were timed repeatedly. After running for a few hours, it appeared ASSERT(app_timer_cnt_diff_compute(drv_rtc_counter_get(p_instance...