Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi,all,
in the Core 4.2, the sentence with word 'Controller' and 'Host' have appeared many times.
like 'When a Host performs the auto connection establishment procedure...
Hello,
I'm using a custom board (nRF51822 QFACA chip), with the optional 32KHz crystal.
When, I use the SDK 5.1.0 and the S120, my code works perfectly. But when I try...
I would like to develop some BLE applications using the nRF52 Preview DK, that embed a NRF52 revision AA. S132 soft device 2.0.0-8.alpha documentation says that is not compatible...
I've been developing some ble code for a custom board. Recently, I just finished creating a new smaller board. When I load my code onto it, I notice that I have trouble discovering...
Can the nRF52 be programmed by 6-pin J-Link Adapter by just connecting the following 4 pins,
Pin 1 : 3.3v Supply,
Pin 2 SWDIO,
Pin 4 SWDCLK,
Pin 5 GND,
Can pins 3...
I want to save custom data in NV address. Which address is safe to save custom data in NV?
I'm working on nRF51822-xxAC with very simple and small code.
And, using s110...
My project for nRFs has a few configurations for different boards.
So, how to enable 'batch build' button to build all configurations by one click? Currently this in disabled...
code.c
ui_flash.c
ui_flash.h
Hi guys,
So we are building the Ibeacon project , and faced with some problem:
The chips falls hard reset periodically when trying...
Hello,
Is there any todo list about how to protect an application from hacker unsollicited copies to avoid illegal clones ?
how to allow jtag in write only (disable...
Hi all,
For PAN 42 which describes an issue write to RAM after a POR. When was this issue fixed? I can't seem to find out what versions of Silicon are subject to this issue...
Hi, i try to understand how to use power down modes. But i have a problem in the example ( nRF24LE1 REGISTER RETENTION TIMER ON ).
while(1)
{
// Register retention mode...
Hi All,
I'm facing unstability in connecting my Central BLE device based on bluez to connect to Nordic Uart service based device.
For every 10th or 11th connection ...
When I use a power supply, (3.0Volts-60mA limitation) with the DevKit boards nRF51 or nRF52 the input voltage is clamped at around 2.0 V and the current is 60mA : the SoC...
Hello, kindly any one tell me how to run a beacon code in nordic Ev kit . I've been trying to make it work . What type of changes i need to do in the code .