I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
I'm using SDK 17.1.0, softdevice 7.2.0 as a Bluetooth peripheral. I'm sending notifications to a paired iPhone. The notifications are keyboard keys, and so are time sensitive...
Hello,
I am trying to figure out how to save a small number of counters to local non-volatile memory on the nRF9160. I have a few questions.
1) How do I determine whether...
Hi
I want to measure chip temperature of nrf52840.
For this I referred " sdk-zephyr / samples / bluetooth / peripheral_ht / src /hts.c"
and I have enabled "CONFIG_TEMP_NRF5...
We are using nRF9160 DK (SDK 1.9.1) with "serial lte modem" firmware. We are trying to test downloading files from a server using AT commands to work with HTTP. The file is...
Upto a week I had *no* problem in programming a nRF52840 dongle with an app I am porting from the nRF52840dk.
All of a sudden I can't get the app running, the dongle appears...
I'm trying to get sprintf working with SDK 17.1. Basically, I'm struggling getting this simply use-case to work. char buf[32]; sprintf(buf, "%.3f", 3,5); I'm not able to find...
I know from zephyr samples that Tensorflow lite is available via zephyr as an external module, though it's not explicitly allowed in the nrf west.yml, and therefore is not...
Hi all, I follow example (serial) to build and run, i already run successfully, but i meet some question. when i use generic_on_off to control light at short time(2s), the...
Hi,
On a NRF52840, I try to perform `x` SPI transactions of 3 bytes each using EasyDMA Arraylist feature fully controlled by hardware. The CS must be toggled between each...
Dear Nordic Experts, The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832. When provisioning, it sometimes...
Hello, All
I am trying the scan_adv example, and use my phone to scan the advertising packet, unlike other peripheral examples, I found that it appears multiple time with...
ncs v1.9.1
Reference nrf\applications\serial_lte_modem\src\twi
This example does not see how to configure the pin.so how to config SCK and SDA Pin?
Thanks!!!
Is it feasible for me to use the 9160 as ble-host and 52820 as ble-controller using just TX and RX lines? (no request or ready lines) My setup is NCS v1.7.0, custom board...
I see that there is definitely support for where a user would cancel the USB host's request to suspend inside of app_usbd.c here's line 1246:
You can clearly see that it...
Hi,
I know that a GPS receiver can can use the Doppler effect to get an accurate velocity measurement. More accurate than the accuracy for position.
However, from my tests...
