SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
Hello,
I'm currently implementing a multi-endpoints Zigbee device using an nRF52840.
This device is a router which have several "GROUPS" clusters (one in each endpoint...
Hi,
I've nrf52840, s140 with SDK17.2 and I was able to set REGOUT0 to 3.3V in 2 ways.
or
nrfjprog.exe --memwr 0x10001304 --val 0xFFFFFFFD
After that I do...
It is my understanding that the more antennas you use for AoA the more memory is required. I am trying to gauge how much memory and resources would I have left for other application...
Is there a way to configure the serial LTE modem application to communicate through the UART using a 2-wire Tx/Rx with Hardware flow control disabled?
I have read that you...
We are trying to switch main MCU that we use in our products into NRF52/53 series devices. We've chosen NRF52833 (aQFN73) for one of these devices. Is it possible to use only...
Hi,
I have a question about the LwM2M Client implementation for the nRF9160.
Can the LwM2M Object updated in a registration update or it is relying on a re-registration...
I have a situation where a customer needs to DFU some nRF52840 custom boards that we shipped. The firmware that I wrote used extended advertising and thus appears as a Bluetooth...
Hi,
I tried running the crypto sample example as part of the nRF SDK project on my nRF5340 DK.
I successfully completed as few tests and then fails while trying to run...
Hello Nordic Team I want to use the ble_app_beacon example found in SDK 15.3 on NRF52810 when NON_CONNECTABLE_ADV_INTERVAL is MSEC_TO_UNITS (5000, UNIT_0_625_MS). The program...
We are using the QDEC in an nRF52832 and our rotation speeds are 0 to 15rpm, usually around 10rpm. Is there any fundamental reason the QDEC can not be used in this case? We...
I'm trying to get the bmi160 sample to work with my custom nRF9160 board. I think the sample is quite old and not maintained. Unmodified (except fixing pure compilation errors...
Hi.
I am building an I2C driver for the Sensirion SPS30 particle sensor (datasheet: https://no.mouser.com/datasheet/2/682/Sensirion_PM_Sensors_SPS30_Datasheet-1888453...
Hello!
Im trying to change my application. Right now everything works with bonding. DFU and reading and writing characteristics. We have noticed a lot of clients unpair...
Hi all!
I'm trying to run the BLE light switch example on the nRF52833 development board using Segger. I get the following error whenever I try to build the client. This...
sorry where i can find the document/spec for the API that we can use to comunicate with LTE stack L3 . Using Zephyr ? threre are some examples that can help me ?
Best Regards...
