Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Hi Mate,
When I test the example of ANT which is named as hrm_tx(heart rate transmitter), after I programed the ANT_s212_nrf52_0.5.1.alpha.hex and the application of hrm_tx...
I'm running a BLE application on the nRF51822. And I have an application timer to keep track of the real time clock. However, when I receive a BLE_GAP_EVT_DISCONNECTED event...
When i load a nRF52 example in Keil µVision 5.17 (for example ble_app_proximity_s132_pca10040)
The i get a indication that the Configuration files are not compatible
I am...
Hi,
I have a strange problem，
I use NUS service connect with phone , send or receive data，after some process，may happen
the keyboard(use GPIOE interrupt) has no response...
I am trying to test the ble_lbs example to understand the basic working principle of the ble custom service using NAN_36 document after compilation followed by the procedure...
Hi,
I am running the sample glucose app on the nordic chip.
On the iOS we have nRF Toolbox.
iOS Version is 8.3.
SDK version of sample glucose is 10.
After sometime...
Hello,
I've made a hardware base on new nrf52. I followed the exact schematic of eval board and requirements.
Clocks seem to be good (32KHz and 32MHz).
A mange to mkae...
hi ,
i want to transfer data using custom profile.
in which i want to have apple midi uuid service (03B80E5A-EDE8-4B33-A751-6CE34EC4C700) and IO characterstics (7772E5DB...
Hi.
I want to change device name to identify multiple devices.
When I am using two device, the initial device name is "device".
If I connect these two device to iphone...
I have an application that needs to minimize its current consumption when sleeping. From the nRF52 manual, I see that UART should consume 1uA when in idle. The total current...
Hello,
I'm using thhe BLE shied, which uses the nRF8001 chip, with arduino Mega.
I'm trying to connect the Rf module nRF24l01 to receive data from another arduino and...
When checking if a read (or write) is authorized can the event contain an invalid handle (Does the handle need to be checked)?
case BLE_GATTS_AUTHORIZE_TYPE_READ:
{
...
hi
in nrf51422
till now this is my code
now how can i send or recieve information .
or tell me for sending information what to read next?
#include <stdint.h>
#include...
Hi ,
I want to call a pstorage_store() function to update the flash content when ble receives the disconnect event.
My doubt is whether i be missing the flash write event...
I am working on a system with dual Bluetooth chips one acts as primary and the other as secondary.
I want these two communicate with a shared resource(Accelrometer)...
