Hi,everybody！
When i install master control panel 3.10.0.14, i can't find nrf.exe in " C:\Program Files\Nordic Semiconductor\Master Control Panel\3.10.0.14\nrf ". Only nrfutil...
Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
In my previous ticket regarding DevAcademy tutorial for nRF 52840 I already mentioned. that starting from lesson 2 iPhone cannot communicate with the board and the VS Code...
Are there any current or future plans to implement Curve25519 (also known as Ed25519) for the NSIB?
It appears that the CryptoCell 310 supports it, and it is recommended...
MCUboot supports software security count based download protection. But it is found that it is not exposed by nRF SDK. It adds the "--security-counter" argument only if
...
Hi All. I am a beginner trying to complete the DevAcademy SDK fundamentals level course, and since I seamlessly completed lesson 1 on the Blinky sample, I reckon my toolchain...
NCS 2.5.2
Toolchain 2.5.1
NRF52840
Hi,
I'm currently power profiling our custom board. So far I've managed to get the current consumption quite low (6.5uA at 3V...
I am in a need to measure a battery level under a constant load. Rather than adding a custom electronics, I am considering using the radio. I believe there is a way of doing...
Hello,
I am attempting to use a J-Link or a FORTE programmer to interface with the debug port to upload a new binary/program to my board. Is this possible? I am trying to...
nRF52840
NCS 2.4.1 to NCS 2.6.1
My project is based on the coap_server example. When I ported it from NCS 2.4.1 to NCS 2.6.1, the network key and PSKC changed. All other...
SDK: v2.6.0. nRF5340 custom board
Hello I'm trying to do an static partitioning scheme using a pm_static.yml file and also I want to use NVS to store some data.
The...
Hi!
First off: I know the Cryptocell register interface is not officially supported, but I'm using it for learning purposes and I'd like to understand what's happening....
Hi, Using ncs v2.7 on the nrf9160, is there a data limit using MQTT to communicate with Azure IoT Hub per message? I'm trying to determine if I will need to chunk my telemetry...
We are developing a sleepy end device using the nRF52840, using light switch sample . The end device is connected to a Zigbee coordinator, also based on the nRF52840.When...
We are using a 5340 with a Skyworks 66112 FEM. Below is our hci_ipc.overlay file.
We are setting CONFIG_BT_CTLR_TX_PWR_ANTENNA =20. When we measure the output of the FEM...
