Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Hi all!
SPI3 Slave project is not built - error:
identifier "__device_dts_ord_DT_N_S_soc_S_peripheral_50000000_S_spi_c000_P_cs_gpios_IDX_0_PH_ORD" not determined
C:\ncs...
Hi,
I want to measure CO2 in different locations using two similar CO2 sensor ( MiCS-VZ-89TE). I can communicate with the sensor over I2C0.
But because two sensors have...
We are facing an issue in nrf52840 (SDK 15). Our hardware uses timer, SPI, USB, FLASH and uDMA. implemented watchdog timer and its working fine as well intented. But in some...
Hi I hope you can help me with this.
I'm using a nrf52833. When I build I see Flash usage of 278044 B.
Regions Size 512KB.
My custom board has this in the Flash0 settion...
Hi DevZone, I am using the nRF52840 to interface an ADS1298 (ECG Chip) via SPI.
I want to test if the communication between the devices are working by:
- Sending a RREG...
Hi All,
How do I disable the BLE stack completely such that I can switch to the DTM stack (DTM example using direct nrf_radio calls)?
Current I disable advertising and...
I want implement beacon function on my Qualcomm BSP board.
However, I'm testing with nRF52 DK in advance.
And need DFU OTA update for my F/W application.
So I'm implementing...
I am trying to configure the nrf5340 audio example to add the ability to update the firmware using a serial connection.
In the audio example documentation, there are a few...
Hi everyone,
I called "bt_gatt_notify()" from workqueue. Usually there is no problem, but when move far away, "bt_gatt_notify()" doesn't return. I called "bt_gatt_notify...
Hi, I'm currently using the Direction Finding Connectionless examples to evaluate using the nRF5340 for numerous projects we have lined up, and I'm having difficulty ascertaining...
Question: Based on the chip nrf52840, I want to design a product application that can work with matter and thread at the same time. Is it possible to implement this design...
Hi dear team, Im currently on the NRF9160 DK (0.9.0) trying to get SPI up and running.
nRF connect SDK v 2.1.1 using visual studio code. However Im having problems getting...
Are the memory-mapped hardware addresses (e.g. 0x40000000 and following)
on the nRF52840 mpu restricted from access by the Zephyr RTOS.
If so, can this be defeated ?
