I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
I have seen this assert since SDK 2.4.2 but less frequent. Now I had updated the code use the SDK 2.9.2, this assert made impossible to release it to production.
The point...
Hi Nordic team,
I am tring to make a BLE mesh net, I use two promicro(nrf52840), one for mesh_provisioner_example, one for mesh_on_off_app_example.
But mesh_provisioner_example...
Hello everybody.
I'm experiencing a problem with two nRF54L15-DK boards, one flashed with sensor clent sample (Client) and the other with sensor server sample (Sensor_srv...
NCS3.1.1, NRF52840, Windows, VScode
I have been trying to add MCUboot to my product, without success.
I believe there are known issues related to debugging when MCUboot...
I'm using the RTT log feature in NCS, and here is my prj.conf:I have two questions:
After using LOG_INF to output logs, I feel the logs are not output immediately. Since...
Hi,
I’m working with an nRF52840 that supports Bluetooth Low Energy updates via MCUboot.
We want to enable APPROTECT on our production units to prevent competitors from...
My understanding is that when the module's measured RSRP is lower than that defined in the broadcasted SIB, ECL will be escalated to higher level during RACH process.
Besides...
Hi,
I found out that my Matter device does not commission to Alexa because as part of adding the device Alexa will try to read FeatureMap attributes from all clusters and...
Hello! I'm working on some project using Fanstel BM832 module. I'm using the configuration based on board nrf52dk_nrf52832, with some minor modifications (led's and button...
Hi:
I'm doing the exercise L3-E1.
I used nRF Connect SDK Toolchain v2.7.0 because it didn't work with v2.8.0
How do I make NRF Terminal appear?
Thanks and Best...
I have a quick question about configure i2c.
I have the following schematic:
And the following configuration for the nrf54l15 :
And the following in prj.conf:...
Once the nRF52840DK is running the Zigbee light bulb demo I cannot flash new code to it unless I disconnect the board and reconnect it first.
I am using nRFConnect for Visual...
Are there user programable once registers on nrf5340 that I could use to store board hardware version? I looked at UICR, but I think they get erased when the whole chip is...
I added FOTA over Bluetooth to my NRF52840 application. Everything works, I can update the application over bluetooth and it runs properly, but after updating if I unplug...
