I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
I'm using dongle nRF52840 to sniff packets between earphone & iPhone.
I am facing the same problem: " Encrypted packet decrypted incorrectly (bad MIC)"
just after LL_ENC_REQ...
HI,
I'm developing it using NRF52832.
I'm updating the remaining battery capacity using saadc. However, the battery value is not stable because the value obtained from...
Hello,
Following to this ticket , I started with an existing Segger embedded studio project from the SDK to port my project from Keil to SES 5.62 .
Now, the project works...
How long does it take to perform a soft reset (using sd_nvic_SystemReset()/NVIC_SystemReset())?
Looking at power measurements (attached) it seems to take about 730 ms (...
Hello developers,
I would like to combine BLE Central with USB HID. I am using the SDK example "BLE_Central_multilink", I can get signal from BLE modules.
Now I want...
I tried to program the Blinky sample which just blinks an LED to the Network core of the nRF5340 DK but doesn't seem to work. However, when I look at the docs I do see that...
Hi
I am a beginner of bluetooth
I want to build BLE connection between nrf52833 and nrf52810 as soon as possible (maybe in 100-200ms)
can I achieve that by config Advertising...
Hi Nordic,
I am facing strange behaviour with nrf9160 aws iot example where I am trying for fota update.
My device is sending data to AWS IOT every 5 minutes as it will...
Hello again Nordic World,
We have been using a couple of the Nordic dev boards (PCA10028, PCA10040) as uart central devices in our test system for a while and have just...
Hello,
I am using \nRF5_SDK_17.1.0_ddde560\examples\dfu\secure_bootloader\pca10040_s132_ble_debug, but when I bulid the proyect the following error appear:
.text is too...
Hello,
nRF SDK v16.0 , Softdevices s140_nrf52_7.0.1_softdevice and ANT_s340_nrf52840_6.1.1
Recently we wanted to add ANT to our BLE application. So we changed the softdevice...
I have an application that I can install and run on the nRF52840 dongle. But to program the dongle, I need to press the reset button and use nRF Connect. So I am looking at...
hello Nordic
i am working with nrf52840, with zephyr (i am new to zephyr)
i am trying to connect to a low power magnetic sensor (si7210-00-iv)
my i2c sometimes works...
I'm testing my own firmware based on the current Asset tracker V2 code (AWS cloud).
The code generally runs well, but when reception drops (simulated by disconnecting the...
I'd like to add an interrupt pin for a SPIM device. (eg. in the following spi_dev: )
&spi3 {
compatible = "nordic,nrf-spim"; cs-gpios = <&gpio0 0xf GPIO_ACTIVE_LOW>; ...
