Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Hello,
I am trying to build the sample/sensor/lps22hh project on nRF52840 DK and STEVAL-MKI220V1, but receive errors in build.
I have added an overlay file as in boards...
Hello, I need support regarding putting my device to low power mode (sleep) and waking up with a timer or GPIO input. I’m working on an application using the nRF9151 DK, with...
Hi! We're evaluating the nRF7002 with its DK. As part of that I'm trying to run the sample in ncs/sdk/v3.0.2/nrf/samples/wifi/raw_tx_packet. I build it with: `west build ...
Hi For the measure of the signal and related audio quality, we would like to measure the transport frame loss. We own two nRF5340 Audio DK. But to be honest at the moment...
Please publish the nRF Connect for VS Code Extension Pack to open-vsx.org so it's available to open source VS Code editors such as Code - OSS and VSCodium . Thanks!
Hello!
I'm preparing a second revision of my first BLE PCB with nRF52810 MCU.
The first iteration worked ok, but BLE range was worse than a ready-made module with PCB...
Hello,
I want to encode a key as a numeric value instead of a string using the ZCBOR library.
I've tried testing this, but each time, the key is converted to a string...
Hi
custom board using the nRF9160, toolchain version v2.6.0, mfw_v1.3.6.
Sorry I can't provide a decrypted modem trace, but I hope the screenshots are enough to show what...
Hello,
I am trying to build the Lesson 9 Exercise 1 in the DevAcademy Intermediate course, related to DFU. I get the following error:
error: SERIAL_HAS_DRIVER (defined...
Hi Support Team
The nRF52832 PS mentions that the pin 44 of nRF52832 QFN48 require no connect. What problem if pin 44 of nRF52832 QFN48 is grounded? Many thanks.
Hello, I'm designing a medical product, aiming at IEC 61000-4-2 level 4 ESD protection, and I have a question on the CC lines.
My understanding is that these two lines could...
Hi, I want to set different gap event length for different peripheral on a ble central: 1 link with high throughput and 4 links with low throughput.
The sdk is 17.0.2...
We are seeing our nrf54l15 based device remain in a high power mode after an ADC read using the latest v3.1 SDK (tested on both rc1 and rc2). This did not occur with the v3...
I've been trying to communicate with an external device which supports up to 25 Mhz on its SPI. So, to improve performance, I'm using the SPI3 at 16 Mhz. I have no issue at...
Hi,
I am trying to add an additional storage partition in flash to my project, however, to some reason, pm.yml file is not getting picked up during the build and I am not...
