In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
We have created a zigbee custom sleepy end device with the base from light switch example. We are able to perform most of the operations successfully.
We have set the following...
in main.c, you have this code
but if you set CONFIG_BT_NUS_SECURITY_ENABLED=n in the prj.conf file, then there are #defines that will prevent the definition of the...
There are two DKs, one works as a slave while the other works as a master. When these two peripherals are connected via Bluetooth, they exchange each other's parameters via...
Dear Support Team
Our customer prepared to develop a triple mode operation game keyboard which communicating over Bluetooth LE, either via the dongle or USB. Should the...
Hello, thank you for taking the time to read this.
I've been reading through some of the forms, and I'd highly appreciate someone with more experience giving me some input...
Hi Support Team,
I’m designing a custom PCB using the nRF52840 based on "Circuit configuration no. 6" from the nRF52840_PS_v1.0.pdf. On our design, VDD_nRF = 1.8V which...
Hello,
I'm making some sensors based on nRF52832 and I'm using them as native transceivers. Maybe I'll look at BLE Mesh in the future but at the moment I just send and receive...
SDK 17.1.0
I developed a firmware that can be used in nrf52833-CJAA-R, but it can't be used in the nrf52833-CJAA-B.
According to the following link:
devzone.nordicsemi...
Hi Nordicsemi Team,
The one of our customers recently purchased NRF52-DK (Dev. Kit) which was Ver 2.1.0.
But This time has issue. He thinks after version 3.0.0. cause...
Hi, I am currently trying to use PWM on nrf9160 DK to control a stepper motor. Do you have any sample code for PWM? Also do you have the pin assignment of which pin on the...
Hello! I am working on a project I have set " sensor/server" as my starting point. The sensor is successfully interfaced with NRF52 I need to store the calibrated data of...
We're trying to develop a device driver by putting it in our application folder (under /drivers).
The west build system now recognises and builds it through the Kconfig...
I am following the instructions to set up NUS shell through bluetooth with the following example: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/bluetooth...
hello
I try to make work the ADC on the NRF52840DK
I would like to use any of the 6 channels on the ARDUINO connector (p0.3, p0.4, p0.28-p0.31)
I am simply not able...
Hi . We have been struggling for months now to achieve DFU updates for our firmware with no success. On our latest stage we get "Can't find room for update". We are just trying...
