In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi i have a problem i put buttonless dfu on my chip and everything went ok i can do OTA updates and everything works perfecly but i have a problem when i connect via j-link...
Hi,
Is there a low power consumption for battery powered long term (months) application for Nordic Thingy 91? I don´t need GPS position, just to receive sensor data and...
Hello
Using a Thingi91 with latest firmware and Asset Tracker v2. Connects to the tower, but cant seem to connect to the NRF Cloud. How can I check if it can reach any other...
Hello all
I am using the Thingi:91 in Sri Lanka. I can connect to the tower correctly, but cant get data connectivity yet. I am told by the operator that they use the following...
On nRF cloud I registered the ibasis sim card which came with the 9160DK and connected it to that 9160DK device. I'm now using a Fanstel BLG840F and wanted to know if the...
hello Nordic
i am using nrf52840, with zephyr
i wish to use the nrfConnect Tx power service to read and to SET my Tx power
but in ncs in zephyr/subsys/bluetooth/services...
Hi,
I am using nordic52840 dk board.
And i want to flash a bin file using nrfjprog command line.
For Hex file i am using below command
nrfjprog --reset --program blinky_pca10056...
Hi everyone,
We are using the nRF5340 and need to use an LFXO, not just for BLE, but also for the real-time clock that our product should provide.
Due to other requirements...
Dear Team,
Just I have purchased Thingy91. Please help with where I can see the demo to start with some basic example of transferring data. Mentioned that Pre-loaded assert...
I just installed the nRF toolchain and Programmer application to start using my nRF52840-DK eval board. I have the board connected through J2 to my computer and I can flash...
hello Nordic
i am using nrf52840 with zephyr ncs
unfortunatly i used this command "pamac install downgrade" at one point
since then i can not use 'west flash --erase...
nRF5 SDK > nRF5 SDK v15.0.0 > User Guides > Developing for nRF52810 gives a list of things to do to adapt an nRF528 32 project to an nRF528 10 target.
But, looking at...
Long story short.
I am trying to merge DFU master code to feed a DFU.zip to the DFU receiver code already present in the secure bootloaders (but elevated successfully into...
I'm working with firmware and hardware that has previously worked properly. I recently migrated to S113 from S140, and changed the data format of what was being set in the...
