I will be selling various ble products. My customers can connect to and program the devices using their bluetooth smart phone or tablet.
I want them to have the option...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hi,
With the NRF Connect / NCS SDK, I can build the asset_tracker and serial_lte_modem without issue.
I want to make my own project, so I copied asset_tracker entirely...
Again I am asking a question I should not because I cannot find it documented.
I get a pairing request from the central. I need to respond with sd_ble_gap_sec_params_reply...
Hello.
Now, I'm trying to make a Beacon with updatable Major Value, based on sample 'ble_app_beacon'.
I'm not really familiar with BLE and Nordic device, though...
I...
Hi,
We have created GATT servers and tried to connect with one MOBILE APP.
But, we failed.
Although, we could able to connect with standalone BLE, but once we tried...
Hi,
I have been trying to experiment with the nrf5 SDK for thread and zigbee. Our product uses a NRF52840 in the form of a BL654 module and we have been using xbee S2C modules...
Hello, I was reading through the documentation for the nRF Connect for Desktop and I came across a reference to set up the nRF Connect for VS Code. However, I couldn't find...
Hi,
I am using nRF52820on a customer board to run MESH Light project, but I can not start the mesh stack, problem is:
it looks like due to flash limited, but according...
Hi All,
I am new to Zephyr/NCS, so I am a little confused about which UART driver (Zephyr's uart/nrf_libuarte/nrfx_uart/nrfx_uarte) to use to approach this feature with...
I'm evaluating the nRF52840_DK with nRF5_SDK_17.0.2
After doing some tests with ppi to timestamp gpio events, I'm now enabling the softdevice.
This leads to two questions;...
I have been successfully using mergehex with s140_nrf52_6.1.0_softdevice.hex and a bootloader to create firmware packages for my nRF52840-based device and wanted to try softdevice...
When I run the QSPI example in SDK, it can work well both on the PCA10056 and my custom development board. However, when I transfer the example to app_buttonless_dfu, the...
Hi,
I am trying to send the max 240 bytes in NUS SERVICE nRF_CONNECT_SDK
I have seen the ble throughput example and changed
CONFIG_BT_RX_BUF_LEN=255
CONFIG_BT_CTLR_TX_BUFFER_SIZE...
Hi Nordic
We are evaluating nRF 9160 for our next revision of the PCB, and we are testing nRF9160DK.
It came with a sim, which i tried to activate by nRF cloud, but it...
Hello
Is there any example or tutorial on how to use the mpu6050 library?
I just started to program the nrf51822 and hope to find some helpful clues to get me going. ...
I have nrf52840/32 dk and lis3dh accelerometer. I have interfaced two of then via I2C. I want to advertise data of lis3dh xyz acceleration values in the ibeacon advertsing...
