Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
I want to evaluate Bluetooth LE Channel Sounding on the nRF54L15, using multiple antennas. The nRF54L15DK only has one antenna, so if I use it as both initiator and reflector...
I am experiencing issues programming my newly purchased nRF52840 DK, which has never been successfully flashed. After following the official starting guide on nordicsemi.com...
When Enabling an advertising set already enabled on the Softdevice Controller, the HCI error command disallowed is produced when according to the BLE specification 6.0 it...
Hi everyone, I am attempting to configure two of NRF5340DK modules to execute ISO_Connected_Benchmark. I have tried to configure ipc_radio to compile for cpunet and application...
Hi everyone,
We're using the "Manufacturer Specific Data" field within its advertising packets to send the firmware version to a phone application. It requires the company_indentifier...
1st issue: Tingy91X doesnt build at all with debug -Og enabled: Because of all the strange issues of Thingy91 (nRF9151) and "not to be used in new products) we ordered a couple...
Hello,
I would have a question regarding the use of PCAL6408A I/O expander on nRF9151 DK. The buttons and LEDs on nRF9151 DK are connected both directly to the processor...
We are planning to run a small proto build, and looking to program a small quantity of nRF54L10, prior to the SMT. These are loose parts (not built onto any PCBA). I am hoping...
I recently switched from evaluating an nRF52805 (Fanstel BC805M) to an nRF54L15 (using the nRF54L15-DK), and after I updated the toolchain and tried to flash the kit (using...
checking in if anyone is successfully using an open debug-probe for nRF54L series?
...guessing nordic is using segger OB on the DK's because of the Risc-V not fitting...
Hi,
I'm evaluating the nrf5340-DK board. I have a question about LED5 state. I tried following power sources:
usb J2, sw9 in VDD position - LED5 lights and I can detect...
Hi,
In the example ras_initiator for channel sounding, there is a macro set for maximum TxPower:
where #define BT_HCI_OP_LE_CS_MAX_MAX_TX_POWER 20
In the...
After looking over numerous other devzone tickets and google hits... I cannot get host name to IP address resolution to function on the nRF9151DK. The original source code...
Hello,
I am working with a board (currently embedded inside a clear container I cannot easily take it out of) with an nRF52832-CIAA-R. We were taking photos of it with a...
Dear support team and community
After some days where it worked perfectly, our nRF52840 suddently stopped connecting anymore to a Motorola G4 plus running Android 7.1.1...
