Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hi all,
I'm working on optimizing the power consumption on my nRF52840 DK and need some guidance. Currently measuring ~5µA average idle current via PPK2, but I need to reduce...
Hello
I am trying to perform a firmware update over Bluetooth but without using the external flash on the nRF52840-dk.
At this point I can successfully build the smp_svr...
Hi,
I have custom hardware using the NRF52810. Due to its very small RAM size, I developed the code on the NRF52DK_NRF52832 and then removed functionalities to make it fit...
Hi The Nordic team,
After my device reconnects to the gateway from offline again, I don't know what I am doing with this timing every 1s. This situation will not happen...
Hi，
I developed a gateway for converting an MCU to ble Bluetooth. The MCU connects to 8 BLE hosts via UART, and each Bluetooth host can connect to one Bluetooth slave. All...
Hello,
I am trying to configure COMP peripheral on my NRF54L15 DK. I am using P1.11 pin (AIN4) as single ended input for this purpose. For now I am trying only to evaluate...
Hello,
I’m working on a project where I intend to integrate the nRF9151 as a standalone modem , communicating with my external MCU via UART using AT commands .
My goals...
Hi,
Currently I am using nRF52840 as nodes for mesh network. However, by reading the sdk5 documents and example, I did not see any clues to update the firmware with DFU...
After the update to extension version 2025.8.654, the extension can no longer find the nRF SDK in my west workspace in the build configuration. If I revert to extension v2025...
I made a PCB board, but I couldn't connect to the chip with JLink. I used a lithium battery to power VDDH. I want to test if there is any problem with the hardware. I tried...
I am using NRF5340 with NRF connect (Zephyr) and logging out to RTT (printk or printf, etc) , which works but sometimes I get buffered fragments and dont see the rest of the...
Product: nRF54L15, SDK:3.0.2, door lock application
Hi,
When the Matter door lock removed from Apple Home(Home App, remove accessory), the lock does not remove all the...
Hello,
I am experiencing an issue when trying to flash any program using nRF Connect for VS Code. When I execute the flash command, my board disappears from the "Connected...
Hello,
Is there support for fuel gauge algorithm with the CR2450 and the nPM2100 implemented? If not, is there a plan to release support for it soon?
Thank you,
Fin...
