In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
I have a custom nRF52833 wired to an Adafruit USB Micro-B Breakout Board, and when I plug it into a Windows computer, it gives a device not recognized message and no COM port...
Hi,
Our custom hardware makes use of an external flash device, IS25LP032D-JTLE-TR, for storing files (littlefs) and OTA updates. We've noticed, seemingly only after a power...
I have an nrf52840dk and tried it with a ble central example and it worked fine. Then now I want to deploy him to the nrf52840 dongle and he appears to not work and I also...
I was trying to build the ble_app_scan functionality in a well served project in my custom nRF52810 board. During project build I am facing these build errors in SDK v17.1...
Not sure where to report this bug but I noticed that when typing sample names in "Create New Application From Sample", some Nordic samples do not show up...
For example...
Hello Sir,
I am working on direction finding. I use the nRF52840 DK to flash the code onto an nRF52811 (custom board) that supports direction finding. In the build configuration...
I was trying to receive some data using "i2c_transfer" then continue the receiving without starting a new transaction.
Stop bit was sent if I configured to use it or not...
My project has a nrf5340+external flash, and an external USB-C connector. The device exposes a USB file system (FAT) which is hosted on the external flash partition, and appears...
Hi Nordic
Q1.
HW: nrf9160 customer board. One USB-to-RS232 cable is used for PC sending AT commands (UART2).
Another USB-to-RS232 cable is used for PC collecting modem...
I am currently evaluating the Nrf54l15 viability for a migration from the Nrf52 for our products. I've been able to advertise, scan and connect with success but I can't find...
Hi,
I'm trying to build the nrf5340_audio/broadcast_source application. I'm getting the following error: nrf5340_audio/src/audio/le_audio_rx.c:20:22: error: 'CONFIG_BT_ISO_RX_MTU...
Hi, I have recently created a board definition for our nRF5340-based hardware using the "Create a new board" feature from the nRF Connect for VS Code plugin. I'm using SDK...
Hello,Nordic team
I am programming with nrf52833 and ncs v2.9.0
I am going to do dfu not by YOUR example(FOTA or UART……)
I flash_write() data to image-1 address，and...
Hello,
Very new to Zigbee. Trying to use nrf 5340 dk as a Zigbee Coordinator to connect to a Thirdreality and a Sonoff PIR motion sensor. No modification (expect adding...
