Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
Hello,
we have a custom PCB with the NRF54LM20B (nRF54LM20B_xxAA_ENGB) and nPM1300, and we are observing odd behavior with the LFXO failing to start from a cold boot, causing...
Hi I have a NRF52833 module in my PCB design. Are there any end of line tests you would recommend at the end of my production line?(end of line tests) I am using a Panasonic...
Hello,
I am trying to get the Nordic MCP to work in VS Code, but every time I try to authenticate, I get the following error:
I am signed into my My Nordic account and...
Hi,
We’re Hydro-Guard, a volunteer student team (TU Delft / University of Milan) building solar-powered acoustic recorders that detect illegal boats in nature parks ( short...
Hi
We are developing a system where 2 devices (NRF52840) advertise to each other (and eventually connect) in a highly reflective environment (the cargo hull of a ship)....
I am developing a proprietary 2.4 GHz distance measurement with two-way phase-based ranging and RTT on the nRF54L15.
I intend to control the RADIO peripheral directly, without...
Hello,
I tried following the exercise until the part where you start a debugging session. I looked at the thread viewer and the result was different than what was on the...
An nRF7000-QFAA (QFN48) is used in a 2.4 GHz-only scan design: one antenna on TXRF<0> behind a 2.4 GHz band-pass filter, no diplexer, no 5 GHz path. Scanning is restricted...
Hello.
When I ran the NCS SBOM command using VS Code, the following error occurred, and the file could not be generated.
I would appreciate it if you could tell me how...
Before buying two nRF54LM20-DKs, I need to know which way is supported. Our own protocol uses RADIO directly: in each 20 ms period a SYNC goes out at 30 µs, started by a TIMER...
I'm working to write a Zephyr-compatible driver for the LP5814 on a board with a nRF5340. The LP5814 is an LED controller that receives commands over an I2C interface. There...
We would like to ask about the three-stage LC filter on the ANT line.
Is the three-stage LC filter required? We are considering reducing the number of stages to save board...
Hi
SDK 3.4.1
Custom Board but with working USB-Interface from App
https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-9-bootloaders-and...
Hello,
I would like to use the Bluetooth Channel Sounding feature on the nRF54L15 for regulatory RF certification testing (e.g., FCC, CE, or Japan Radio Law).
Is there...
