I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hello,
I've recently created a custom board based on the NRF52820 which is configured based on the datasheet.
I'm using an NRF52833 DK OB J-Link to program the device...
Hi,
I use the modified version of the USBD example(nRF5_SDK_17.1.0_ddde560\examples\peripheral\usbd) in nRF5 SDK from here . (My development kit is nRF52840DK.)
And I...
Hi, I have configured normal uart, where you send 1 tx_buf and wait for the rx_buf until you get a response. This setup was fine until the logging feature was requested. However...
Hi, I am developing a product using BLE with nrf52832. We are aiming for a BLE communication range of around 1.0m. However, if txpower is set to -20dbm, BLE communication...
Hi,
I found this forum post about the Verizon APN:
https://devzone.nordicsemi.com/f/nordic-q-a/46288/nrf9160-verizon-sim
This implies that I don't have to use "AT...
I want to parse the following JSON { "ver": 3, "mode": "online", "custom": { "apl1": [ "off" ] } }
Tell me about how to parse json and how to write code
The keywords...
Hi Everyone,
I am developing a PC App. with nrf52840 usb dongle (central) to communicate with nrf52840 BLE device (peripheral) on long term and transport data. Everything...
Hi,
I was working on nrf52840 DK and I left it a few weeks and came back to use it and I discovered that the whole USB connector (J2) got removed. Not sure if there are...
To the kind attention of Nordic support team,
I'd like to know what would be the best theoretically way, if possible, to control "when" multiple notifications are sent...
Hi,
I am developing with the nRF52833 DK using NCS v2.00.
I have edited the existing TX power service (TPS) to allow the client to set a desired TX power. I have added...
I'm using the nRF52840 with NCS SDK 2.0.2 and need to be able to change the BLE advertisement name of the peripheral device dynamically.
I have this working when using ...
Hello Devzone,
I am building firmware for an nRF9160 based device, starting with an ncs 1.6.1 sample app and LTE modem firmware v1.3.1. I'm in North America, and when testing...
I am using the SD card driver from nRF5 SDK v17.0.2. Device nrf52840, IDE Segger, Custom PCB. nRF52 DK as progremmer.
There are problems when deinitializing the SD card...
Hi,
I am developing a peripheral in ble, and I receive the following error when I disconnect a new connection within the connection callback.
bt_conn_disconnect ( conn...
