I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi there,
We are using nrf9160 DK v1.0.0 ( pca10090 ). SES version 5.68 nrf Connect SDK 1.9.1 Windows 10
I want to make it as spi slave on pins CS=p0.10, mosi=p0.11, miso...
Hello Team,
We are developing an application with nRF52832 and ncsv1.8.0.
We are using NUS service to share data between Mobile and Nordic Chip. With the help of nRF...
Hey there!
The DFU over serial was successfully implemented. Unfortunately, I was only able to update the first node of my mesh, not all of them.
The first node in the...
Hello!
Recently I want to write a hci vs command in zephyr using nrf connect sdk, when I track ncs_v1.9.1\zephyr\samples\bluetooth\hci_pwr_ctrl samples code and find it...
Hi, for nRF5340 the "Build code" is a string of 3 chars
H - Hardware version code P - Production configuration code F - Firmware version code
https://infocenter.nordicsemi...
Hi
I am testing a thermometer peripheral using the nRF52840DK. It is advertising using BT LE Coded (BT_LE_ADV_OPT_CODED) with an advertising frequency of 3 seconds.
...
Dear Nordic Support Team,
I would like my nRF9160 DK to connect to multiple servers using TLS. Among others, I have read the following documentation: nRF9160: Simple MQTT...
APN setting of nRF9160 cannot be done well.
I am using soracom's SIM, and the contents are as follows.
(When I checked, it was a SIM that supports LTE-M.)
Name: Any (Example...
I'm relatively new to both nRF and Zephyr platforms and I'm wondering how to disable UART on the UART pins (such as p0.19-p0.22 on the nRF5340 that I'm using) so that they...
WHAT IS THE MAXIMUM OUTPUT CURRENT OF DCDC IN NRF52833 OUTPUT IN HIGH VOLTAGE AND NORMAL VOLTAGE MODE?
I AM POWERING UP TWO SENSORS WITH IT THAT USES CURRENT IN MICRO AMPS...
Hello there,
I am developing a door lock system. Where in final product door lock will be controlled and monitored by BLE+ZigBee. So far I have complete success of controlling...
Hi,
Much like the poster below, I have ran into some issues during FOTA when my flash usage gets VERY CLOSE TO 100% (Much less than a page left), disabling some features...
