I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
Device: nRF52840 Softdevice: 140 SDK: 17.1.0
I'm trying to develop a custom bootloader that will determine which of two images (A or B) to jump to. The memory map that I...
I noticed that if I set options = BT_LE_ADV_OPT_NONE in bt_le_adv_param I get a random address at each bootup and if I set it to BT_LE_ADV_OPT_USE_IDENTITY I get always the...
Hello,
I'm currently working with ISP2053 which is the nRF5340-based module.
The system, as the specific GPIO pin detects a low-to-high event, gets data from another...
Hello guys,
I'm trying to run uart example from https://github.com/andenore/NordicSnippets/blob/master/examples/uart/main.c extended by interrupts call after transmission...
Hi.
I cannot build a ble_app_uart Nordic example that I was able to build flawlessly three years ago and later. I wonder if anybody could give me a clue on what's going...
On Zephyr `2.7` I have following code to setup a SPIM on a custom board: Device tree:
main.c:
Now this no longer works on Zephyr `3.1`. I temporarily tried it with ...
Hello
I tried to install nRFConnect for Desktop, the latest version When I try to launch Toolchain Manager, I get an error "Unexpected end of JSON Input" error message....
Hello,
I works with Zephyr, VCS, SDK 2.0.0
I don't find how to get pin number from the DTS pinctrl .
In this folowing code, I want to replace magic number (uplighted...
Until toolchain update it was working well. But after toolchain update I cant even open toolchain manager . It just shows some exception like " Unexpected end of JSON input...
using NCS 1.9.1 - Zephyr - Segger Studio - sample code: bluetooth / peripheral_uart
I based my project on the sample, modified it slightly and it works well on a board with...
Hi,
I saw here: nrf52840 802.15.4: mlme_start_req: nonbeacon-enabled mode doesn't work
that the SDK-Version 14.2.0 was not compiled to work with non beacon enabled mode...
Hello,
After upgrading to the new version with the help of the migration guide, there is an issue that I could not trace back to any changes.
If I am correct its about...
Im compiling an app in nrf sdk 2.0.0 which works well on the nrf52811
as soon as I add
CONFIG_NRF_802154_RADIO_DRIVER =y
into prj.conf
without even initializing...
