I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I have tried installing the nrf connect 3.11.1 on 2 different windows 10 machines. Both are clean windows 10 installs. The hard drives were wiped and windows reinstalled....
Hi,
the following event is generated when I connect two or more nRF9160DKs to a Windows machine: "Disk 2 has the same disk identifiers as one or more disks connected to...
1. 2. 3.
I am using the ble_app_beacon example as the starting point for my project. I am working on a project where a number of beacons will advertise its identity and...
How do you enable any of the i2c peripherals on the nRF9160 dk boards?
I tried changing the device overlay to the code below:
& i2c0 {
status = "okay" ;
compatible...
Hello,
I have a project that uses JWT.
When migrating from nRFConnect SDK 1.6.1 to 1.9.1, build failed with message: multiple definition of `default_CSPRNG'
The error...
I have
Hardware: nRF52840 DK - 1 nRF52840 Dongle - 1
Software: nRF5 SDK Mesh - v5.0.0 nRF5 SDK - v17.0.2
I want to program Mesh Serial example on nRF52840 Dongle using...
I try to using nrf_fstorage_write() to write data to fstorage and then waiting writting finish. But it hang at sd_app_evt_wait().
int _fstorageWrite(const uint32_t addr...
I try to integrate https://github.com/NordicPlayground/nrf5-calendar-example into Keil project. But the following error messages shown when accessing NRF_CLOCK.
error messages...
Hello.
I have a question about programming a dfu + softdevice + app code using j-link.
I programed like below for using wireless firmware update.
program softdevice...
Hi,
in my application I have setup the nRF52 to wake-up from deep sleep if a low value is detected on either of two GPIOs (4 and 5). What I'm trying to achieve, is to be...
Hello,
with my nrf52dk board i had made some tests to check the scan performance.
Using nrf Sniffer - with Wireshark
nrf Mesh - LightSwitch Client (Mesh SDK v4.2...
Hi,
Automatic installation from ToolChain Manager, no errors. Perform west update ,no errors. Check all the files ,no problem found.
Have reinstalled NCS for many times...
Hi,
Using MeshSDKv5 on custom nRF and nRF52DK
We are working on an LPN wireless PIR sensor so which sends a sensor status publish message on occupancy.
I have notiiced...
Hello,
I want to keep perform some task periodically .. probably using tick timer / rtc / application timerof every 5 ms, to perform some task, without keeping the thread...
