Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
I'm getting a strange amount of error when trying to measure the battery for a custom PCB based on the nrf9160.
Details
My VCC_IO is 1.8V
My max battery voltage is...
Hi,
Perhaps I have a misunderstanding of this GNSS Socket Option.
In the GPS Sample Project (samples/nrf9160/gps) with a nrf9160-dk and no connected GPS Antenna, I set...
Hello, I am trying to add a watchdog timer to my code which consists of THREE threads, so I referred to the task_wdt example in Zephyr/Samples/Subsys for SDK1.6.1.
Based...
Hi,
I wonder if there is a smart and easy way to implement a fallback if I use the MQTT connection with a static IP. What I want is if the IP fails to connect it tries again...
this error shows after the 100% completion of memory flash as shown in the screenshot below. after showing the error , nrf52840 pulsing led turns off automatically.
Note...
Greetings All,
I am trying to connect an nrf52840dk board to an nrf52840dongle for wireless serial communication.
I flashed the nrf52840dk with the central_uart sample...
Hello,
I am using nrf52832 and i am using a SW similar to the beacon.
I tried 2 configuration:
tx_power = 0 (0 dbm)
tx_power = 4 (4 dbm)
I tried to measure the...
Hello,
I'm familiar with the GPIO and GPIOTE peripherals,
The GPIOTE has 8 channels, so it can use 8 GPIO pins to fire interrupts.
Some questions:
- Can the 8 Channels...
I've successfully built the 'direction_finding_connectionless_tx' project and flashed that to an nRF52833dk, and built the 'direction_finding_connectionless_rx' project with...
Hi,
I'm using a NRF52811 on a custom board and I would like to change a project from a NRF52832 with S132 to it.
I only use supported functions from the S113, but I...
how to set the High-drive QSPI?
NRF_GPIO_PIN_H0H1
nrf_gpio_cfg ( mosi_pin ,
NRF_GPIO_PIN_DIR_OUTPUT ,
NRF_GPIO_PIN_INPUT_CONNECT ,
NRF_GPIO_PIN_NOPULL ,
NRF_GPIO_PIN_H0H1...
Environment:
- OS: Ubuntu 20.04 (Docker container)
- NRF SDK: v1.4.0
- Zephyr: v2.4.0-ncs1
I am trying to build my project for native_posix. I am getting some build...
Hi, I have a NRF52840 DK. I want to use ble_app_uart_c and my peripheral is NRF52840 Dongle and also I want to receive and transmit special frame over ble. I have a problem...
