In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hello,
I am using the nRF54L15-DK development kit. The peripheral-uart example works well to stream data from the kit to a smartphone using the nRF-tools App. However...
I am trying to use the ADC on an nRF52840DK.
I have configured the two ADC channels in the overlay
I setup the channels like this
and take readings using this code...
Hi, I have faced dificulties calling zsock_poll for ZSOCK_POLLIN with multiple opened sockets, expecially when conbined TCP and UDP at the same time. My goal is it poll for...
So when I toggle the pin high, it gets set to 1.8V. I want it to be at least 2.8V. I did configure the VDD to 3.3V. The VDDIO does show 3.3V, but a pin like let say P1.11...
I have been trying to use the ` nrf\samples\bluetooth\peripheral_nfc_pairing ` sample code on the nRF Connect SDK v3.0.2 to connect to a Samsung Galaxy A16 5G phone.
The...
I bought a tiny board on Aliexpress from HolyIOT. It comes with an nRF52832 and an LIS2DH12 accelerometer. The silkscreen on the board says HOLYIOT-21011-v1.0.
This schematic...
Hello,
We are developing a board with both nrf91 and nrf54 boards. We are looking to make the nrf91 a SLM with a UART interface to support the LTE functionality of the nrf54...
Hi, I have two concerns about the functions nrf_gpiote_subscribe_set, nrf_gpiote_subscribe_clear, nrf_gpiote_publish_set, and nrf_gpiote_publish_clear. The expression
*...
Hello,
I'm trying to figure out why I get this warning that seems to block the compilation process but a bit of context first :
I'm resuming a project that was paused...
Hi,
I am trying to create a new board, following the Exercise 1 – Custom board for single-core SoC (nRF Connect SDK Intermediate), but I am getting this error:
Does...
Hi,
After I executed nrfjprog --rbp ALL , how can I unlock the chip so that I can program the board again?
Currently, the only way I can program it is by running the following...
Dear Nordic Devzone,
I have some questions regarding battery profiling procedures.
1. Is it normal for battery profiling to take longer than 8 days? As you can see in...
If i want gsm am uploading one file and if i want gps am uploading different file(SLM shell). Now I want both GPS and GSM to work in same file which needed to be uploaded
Hello
i have a design limitation for height in my product and i need to find another inductor with a max height of ~0.5mm can you please share more information regarding...
