Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
We are connecting nrf boards to solar charged batteries for power consumption. We will be remotely deploying the boards on field. The boards are connected to sensors, from...
I'm going from v2.6.1 to v2.7.0; I'm using a thingy53. I'm getting a voltage error prior to boot.
[00:00:00.002,929] <err> voltage: setup: -134 *** Booting nRF Connect SDK...
Hello.
Wiring 1:
wiring 2:
Background to the case: We tested this with 2 different ppk2s and always got the same results. Our custom board works fine if we wire...
Hi,
I evaluate MCUBOOT and trying to understand how it works. I am using a nRF52840DK. I have base my demo on this course ( Exercise 1 - DFU over UART - Nordic Developer...
Hi,
We would like to disable all wakeup sources before calling sys_poweroff. How to achieve this using Zephyr API? Pin configuration should remain as previously configured...
Hello,
I'm trying to enable the Power management for nRF9161 over nRF-Connect SDK2.5
the prj.conf has an entry of 'CONFIG_PM=y'
but it not accepted because we do not...
I am running the demo about knx iot. (branch: v0.3.0_rc in https://github.com/NordicPlayground/nrf-knx-iot )
I build and run "light_switch_sensor" and "light_switch_actuator...
basically, I want to use dm feature in connection-oriented communication. not in connection less, and I want to connect 1 central to 4 peripheral and measure distance.
Can...
nRF Conncet for Desktop v5.0.0
Hello,
I have some trouble to update the Toolchain Manager of version later than v1.2.6. The download fails. However, I can download the...
Hi,
We are working on a project using the nRF52832, which utilizes UART for a QR-code sensor, I2C for an OLED display, and SPI for external flash memory.
We are at the...
Hello.
I am trying to write protect the Flash area using nrf52840's ACL peripheral. I tried to perform the same process on the main processing side by referring to nrf_bootloader_flash_protect...
Hi friend,
I use SDK16.0, and the version of softdevice is S140 V7.0.1. Can I advertise a special data? like 0x08,0xff,0xa6,0x02,0x33,0x09,0x55,0x00,0x0c. 0x08 is packet...
I am looking for to buy(I don´t have a 3D printer) a enclosure to protect my nRF52840-DK. It is not a good practice to handle because probably soon this practice will damage...
Hello, I just receive a nRF9161 Development kit and I'm completely new to both nRF9161 and Zephyr.
I want to start an evaluation project based on the nrf9161 lwm2m client...