Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
I have an issue with the ble_app_lbs. I can compile it OK, but when I run it it gets as far as calling sd_ble_gap_device_name_set(), which returns error 0x3001.
Can someone...
Im writing a serial bootloader for the NRF51822 128kB. Im not using much of the SDK and its a custom protocol i.e. no bluetooth. The boot loader can be squeezed into 16kB...
I looked at a very similar thread that had this title for MacOS and I feel that my issues are the same however changing the hardware debugger only changes the error I get...
Halo, is there any linux ( possibly debian or even better raspbian ) driver for
nRF24AP2-USB dongle?
Do you have ANTware II linux ( possibly debian or even better raspbian...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
I'm using Keil to debug my application. Softdevice was loaded w/ Studio and when I click on Debug Keil loads the code but it does not stop at any breakpoint I set. It does...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hi,
First I'm new to these devices and BLE in general.
I am however very experienced at embedded design and Keil tools and ARM processors.
I have got the demo heart beat...
I have the ble_app_hrs communicating with the ble_app_hrs_c, and everything works OK. However, I have to be able to send data in both directions. How do I modify, or what...
I am developing a device converting adc input into data and transmitting them and receiving them at other place,I cant figure out between analog input eg:AIN0 and the port...
Hi,
I'm using nrf51822 with s110 softdevice v6
My question is the following.
How many devices sending advertising messages can be detected at a time by a central unit...
Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
