Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
To the kind attention of Nordic support team,
About nRF52833 product specifications (8. recommended operating conditions)
"Note: The on-chip power-on reset circuitry...
Hi,
I'm trying to run a pc-ble-driver on Arm64 arc
I've compiled the pc-ble-driver to arm 64 from this release: ARM64-linux pc-ble-driver origin/release/4.1.2
I used...
Hi,
I'm currently working on a way to connect raspberry pi as a gateway into the nrfcloud. For this case, I used nrfcloud/gateway-raspberry-pi. Neverless, when I tried to...
I am developing a product using nRF9160 and found the power consumption is higher than the datasheet. So I want to use Matlab ti simulate the circuit to see where the error...
I am currently trying to implement a Thread functionality on an nRF Dongle connected to a windows machine. Its intent is to be able to recieve messages from other thread components...
Hello Nordic team,
I have a nrf9160 powered from a 3.8v bench supply.
I also have a usb to uart cable , with uart wires going into NRF9160. Usb side, plugged into my computer...
Hi
1、 The following table does not indicate whether the QDID belongs to 5.1 or 5.2.Are the QDIDs of softdevice classified as Bluetooth 5.1 or 5.2?
2、The following qdid...
Hi all!
I flashed and got both SoftDevice s130 and the example code onto my nRF51802 without prior modifications.
I flashed softdevice according to: https://infocenter...
Dear Nordic Team,
Hope you all are doing fine.
I have the NRF52-DK based on the NRF52832 BLE IC from Nordic. I wanted to implement a basic BLE Beacon that broadcasts continuously...
Hello,
I am starting to work on a sample project, wherein I need to replace the existing "main.c" file I have with "main.cpp", by copying the contents of "main.c" into...
Hi zone,
I've just got nrf9160dk and test gnss feature. Issue is: 1. Device get long time to fix. Even which many SVs in tracking and using
2. After got fix, device...
Hello there,
Recently I tried to configure the MCUBoot on my custom Adafruit feather nrf52840, based on the Windows.
Firstly, I followed the instruction below to configure...
Hi
I use PCA10040DK,My connection description：
DK's External supply + to the PPK2 logic port VCC pin DK's External supply - to the PPK2 logic port GND pin DK's External...
