Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Dear all,
Can I achieve ble peripheral whitelist advertising without peer manager? (Assuming central address is already known)
Following are several places that I've...
I have been using the PPK II for about a month.
I just upgraded my nRFConnect to 3.7.1 and when I run the profiler, the PPK II is no longer visible (the big green window...
Hi,
We are design custom Board using nRF52840 SOC.
We are operating it in Normal mode, using internal DCDC converter
We have used configuration 5 from reference design...
Hi,
We are design custom Board using nRF52840 SOC.
We are operating it in Normal mode, using internal DCDC converter
We have used configuration 5 from reference design...
Hi, There. I am preparing to program a Mesh application based on nrf52840. The application supports the recovery from the points of power off.
So, I have a question. It...
Hi,
I'm working with the peripheral_uart example in ncs 1.6.1 and wanted to enable flow control for uart0, but do not see a way to do that.
How do I enable flow control...
Hi, There,
I develop a communication application based on a beaconing example on nRF52850 DK.
I don't know where I do wrongly. It is always stuck in the "bearer_handler_action_enqueue...
Hi,
I'm trying to collect modem trace from a custom nRF9160 board which is connected to the PC with a FTDI FT2232 UART-USB converter (USB vendor id 0406, product id 6010...
All - We have an nRF52340 based design which when tested with the system off demo available in NCS v1.5.1 gives a system off current of <1uA.
We have a second design using...
Hi.
I just downloaded the new nRF5 SDK v17.1.
The first example I tried, the ble_app_template, the Keil uVision project for pca10056 is setup to use a fixed device pack...
Hello,
We are using an nRF52 DK as part of our QC process to send test commands to one of our devices and record responses. However, I think that the people running the...
Hello! I'm reading the documentation that exists for the nRF5340 and struggle a bit about the Secure attribute unit (SAU) If you read the ARM documentation about TrustZone...
Hello.
I am developing Central device which support LESC.
I have some question about connect to Servers which have diferent LE security
for example case, one of...
Hello,
I am using nrf sdk 1.5.1 and trying to connect the Nrf ZigBee router(light bulb example) with Digi Xbee Coordinator but it doesn't seem to connect. I observed the...
Hello all,
I'm interacting with some nodes in a test network:
setup: 10x nrf52840 DK (PCA10056) boards loaded with the following software.
1x Coordinator ( Zigbee CLI...
