In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Currently I want to build the light_switch examples from the nrf5_SDK_for_Mesh_v2.2.0 on my nrf52832 dev board but this gives the following error "boards.h: No such file or...
I would like to know if Nordic has implemented software support for CryptoCell-312 (nRF5340) in the latest master branch?
Right now I am able to use mbedTLS "frontend",...
Hello All
Please tell me about nRF Connect (iOS).
When the module and nRF Connect (Ver 2.0.1) are connected using LESC, they will be disconnected after bonding is completed...
I am using the ble_app_uart example and I am having a hard time finding the function that writes a UART message to BLE from the Nordic to the host. uart_event_handle() seems...
Hello All,
I am working on nRF51822 use SDK nRF5 12.3.0 version in IAR workbench.
I am write data in the flash so for that i follow below steps,
Step 1: press button...
So, I need to send and receive a data frame with 39 Bytes with a system Dongle-Arduino(with a nRF24L01 module).
My problem is, I tried to configure Dongle to communicate...
Hi,
I cannot update the firmware on the nrf9160 MLM1 Preview development kit we have. Is this possible? or is the devkit voided for the latest nrf connect and nrfjprog...
Good afternoon everyone,
I'm trying to make a working application for the BLE NUS example but with the support of FreeRTOS that is MANDATORY. I work with KEIL. I started...
with NCS v1.3.0 is there a way to turn off partition manager? I want to be able to build my app and mcuboot separately and not use partition manager at all.
Is it possibe to upgrade nRF52-DK on board programmer to program nRF52840? I already have this nRF52DK but in final I found that 52840 will be better choise for my proyect...
Hi, I am reading the datasheet of both the sensor. but i2c register are different.
I am currently work on vl53l1x. please give me the response as early as possible. thanks...
Using SDK 16.0.0 on an nRF 52840 board.
Managed to get a board into a state where it had only data pages and no swap pages, and therefore fds_init fails with the NO_SWAP...
I want to use nrf SPI driver for SPI flash implementation. For that want to send either SPI transmit or SPI receive at single instance to write or read flash address. But...
Version: Mac OS X 10.15.5 (19F101)
I'm using the nRF Connect app Getting Started Assistant and manage to get through most of it. However, when I use Segger to open up a...
Im trying to run http_client example in zephyr folder (ncs\v1.3.0\zephyr\samples\net\sockets\http_client). When i debug, the app run to fault, i dont know what fault but it...
