I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
In previous SDKs (e.g. version 15.0) the following macros were defined in app_util.h
As described in this post these needed to be modified to support more than 15 connections...
I am trying to do the segger development for the 9160 lte ble gateway. When I do the setup info for segger I keep getting a popup saying it can't find the .emproject file...
Hi
I'm working my way through learning how develop BLE Services and Characteristics for an NRF52840. I'm using the 'ble_app_template' example from the SDK (version 15.2...
Hi,
I have the following lines:
NRF_LOG_ERROR ( "This is an ERROR message." );
NRF_LOG_WARNING ( "This is a WARNING message." );
NRF_LOG_DEBUG ( "This is a DEBUG...
I am inquiring about an issue with the SPIM communication. I am reading the who am i sensor of an MPU9250 and it reads 0x71, as it should most of the time but not always....
uVision V5.26.2.0
Error #541: 'NordicSemiconductor::Device:Startup:8.24.1' component is missing (previously found in pack 'NordicSemiconductor.nRF_DeviceFamilyPack.8.24...
I have a complete implementation of OTA DFU where iOS app performs a DFU to a nRF based BT Device. Now i am implementing a fix for the situation where:
During DFU, if...
Hi,
I am currently having issues compiling the thingy52-mesh-provisioning demo from github with cmake. The Readme talks about using SES to compile it, which works fine,...
Hello, I have read multiple postings on this problem about how you have to "forget" the MCU on your android to reconnect through Bluetooth. This does not fix the problem at...
Hello,
I am having an issue where the nRF52840 dongle does not properly reset. I'd appreciate it anyone can help.
I was evaluating the DFU options, and erased the IC in...
Hi,
I am currently using the nRF52832 and I just recently realized that it does not have USB capabilities. I am building a custom board with this chip and I want to use...
My environment: SDK 15.2, SD 6.1.0, SES 4.12
I can build and run the BLE blinky example on the nRF 52832 DK with no problems. I tested LED on/off by writing to the BLE characteristic...
All,
We have an issue with the data transfer rate between a device that uses a nRF52480 (Rigado-340).
We are sending a number of data chunks, approximately 400, where...
Hello,
Now, I am merging my UART code with the TWI sensor example (I use SDK 13). Now my error after compiling the code is:
In file included from ../../../../../../components...
Hello, i recently used a gateway to sensor example and am unable to revert back to factory program of nrf9160 DK.
I toggled the switch 5 to nrf52840 and flashed the first...
