Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I am currently working on encrypting "Provisioning public key PDU" with a public key of end node that was received out of band the by provisioner before transmitting it to...
Hi, all:
I use 9160DK to test GPS standalone mode as follow steps with AT command example：
Approach 1:
1、set ”AT+CFUN=0“ to power off mode;
2、set " AT%XSYSTEMMODE...
Hello,
I am using three nrf52840 DKs to test sending gatt notify data. They are one peripheral and two central.
When they each have only one Gatt Customer Service, peripheral...
Hello,
I'm facing a problem in pc-ble-driver-py. I adjusted the uuid_count, but the code still fails at the service discovery line:
ble_adapter.service_discovery(new_conn...
I try to use st25r3911 and try to achieve low power consumption.
The code configures interrupts: gpio_pin_interrupt_configure_dt ( & irq_gpio , GPIO_INT_EDGE_TO_ACTIVE ...
Hello,
I work with the Zigbee Light Switch exemple from SDK 2.7.0
After association, the device never use the Poll data as for end_device role. But, it sends continuously...
We have created Thread Network include Leader, router and end devicewitch nRF SDK v2.5.0 on nRF 52840
We found the Thread connect will offline after 15 minute and not reconnect...
This is a higher-level question because I'm having difficulty finding concise and clear practices for this sort of thing. I don't want to go implementing something subpar...
Hi folks,
I'm making an application which needs to transmit a few kB of config data (for a configuration utility), and I was hoping to do it via UART.
To that end, I loaded...
I am working on specialized PCB's for my job, and we are trying to capture modem traces for our devices. Via JTag, I have serial access to pins P0.05 (TX) and P0.06 (RX) of...
Hi All
I m developing a project in nref9160, in GNSS part, I need to use PGPS, but can I control the checking in nrfCloud? sometimes it go to download PGPS and make GPS...
Dear Nordic Developer Zone,
I am working on MAX30003 ECG ( https://datasheets.maximintegrated.com/en/ds/MAX30003.pdf ) with Nrf52840-DK. My sensor is work on the 32.768kHz...
Hi,
I have been having quite a lot of issues around connectivity and my device, all of which at this point has stemmed from MNO blocking activity from MVNO's ( here and...
I tried adding DFU capability to the broadcast_audio_sink sample. At first i copied the whole sample code to a different directory and opened that folder in VSCode which has...
We are running into an issue of stability with our LTE connection. Our nRF9160 makes a call every 5 minutes to our backend. On start-up, the device connects and starts making...
