Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
We have a custom board with an nRF5340 connected to a W5500 ethernet interface. The interrupt handler for the W5500 is never executed, despite the interrupt signal being asserted...
Hello, In the DevAcademy lessons I'm currently running blefund_less2_exer1 on the nRF52840 board. Successfully build and flashed firmware using Visual Studio Code enfironment...
Hello, I am trying to find out my nrf 52840 chip revision. I have tried using the NRF_FICR register but I couldn't find the revision there. I found that the variant is AAD0...
Hi
This is a project that reads sensor data and transmits it to the phone. Currently, the sensor data is read and transmitted to the app.
However, if there is 0x00 in...
anyone can tell what is the "Top right-hand side" sector?
Please see below screenshot.
Left hand side is what I dragged and dropped "merged.hex" from \asset_tracker_v2...
I am working on a module MS12SF1(nrf7002+nrf5340). I am using wifi,ble,sdcard,uart and https functionalities in my code. Currently my flash usage is 72.44%. I also want to...
Hello,
I have an aplication that connects to a LTE network and sends periodically a post request with some information to a http server. To get IP server address, I use...
Hi all,
I have an issue with putting my second boot slot on an external SPI flash. There are more people on the Q&A with issues in this realm, but none that I found were...
In our custom board, nrf5340-nrf7002 ,using external RTC ECS-RTC-SOP8-5101A RTC module, which is connected via the I2C bus.
We have configured the RTC's /INT pin (P1.01...
I am using a nrf52840 dongle. I have my own device which has BLE and I am connecting to an app in mobile phone our bluetooth. My goal is to check for the security level what...
Hi , on this code there are not any problems, ,it runs good. but the problem is current.it is 36uA. it is more than ecpectation. because in datasheet.
adxl362 current consumption...
nRF52833 Onboard jlink is broken what to do?
nRF52833 Onboard jlink is broken what to do?
Who can tell me how to make it work, and nRF52833 comes with Debug in and Debug...
Hello, I am using the peripheral_lbs example project and build it for nrf21540dk_nrf21540
I also added CONFIG_SERIAL=n, CONFIG_UART_CONSOLE=n for disabling uart.
But still...
Hi all
I currently have a project where i send and receive commands over UART to another chip. When i receive a message over UART, a callback is triggered and I continuously...
I am having difficulty getting the nrf_regulators_system_off function to work correctly on newer versions of the Connect SDK.
In earlier versions v1.3 and such, the call...
