Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi,
I work on a project that uses the dfu target library for firmware updates. This has been working flawless until I added task watchdogs.
The problem that I see is that...
Hi,
I am using a ISP3010 SiP which inludes a nrf52832, a DW1000 and the corresponding antennas (built-in antenna).
I have a custom board (board1) as reference, where the...
I added custom data to default asset_tracker_v2. The custom data is properly encoded and displayed in JSON format in LTE and acknowledged by Azure IOT, but it seems that the...
Hello,
We're working with nRF52833 & nRF52840 and I'm trying to figure out why we've ~0.3ms IRQ Latency from the moment I call the function " uart_irq_tx_enable (dev );...
Im building a wireless sensor network for farming applications and the issue I face is that when I supply the nrf52840dk from the external supply pins (P21) I get like 25μA...
Hi,
My customer use nRF52840 with nRF5 SDK 15.0.0.
They have come up against the difficulty that uart RX pin instability.
I have searched the DevZone and it's advised...
Hi Nordic Community
I have been building a thermometer device from which I would like to send temperature values via periodic advertising.
I have based the sender and...
HI
I am beginner, I have a question , is necessary to put both crystal in circuit configuration?,
in my application i am using nrf_calendar example like a watch, may be...
Team,
I am using nrf52810, sdk 17, sd112.
I have setup a write characteristics, to receive some long data ( 64 bytes)
// write char memset(&add_char_params, 0, sizeof...
I added ring buffer and UART ASYNCH interface to asset_tracke_v2. I added CONFIG_RING_BUFFER = y, CONFIG_SERIAL = y and CONFIG_UART_ASYC_API = y to prj.conf file. The build...
The nrf52 is waking from a sd_power_system_off() and resets. The reset reason register indicates it was from a DETECT from GPIO, yet the LATCH register is 0 and all the sense...
I'm interested in zephyr to make the image file lighter. Have a any solution to update for BT DFU with signle bank? I wonder I can use single bank like Nordic Softdevice.
I have been decoding a BLE advertising packet, I am getting correct preamble and access address but once I try to decode the PDU starting with the header it is incorrect....
I am posting this query again as the previous query is closed and unanswered https://devzone.nordicsemi.com/f/nordic-q-a/88349/increase-zigbee-max-endpoints-for-nrf52840 ...
