Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
Hello,
I am trying to figure out how to save a small number of counters to local non-volatile memory on the nRF9160. I have a few questions.
1) How do I determine whether...
Hi
I want to measure chip temperature of nrf52840.
For this I referred " sdk-zephyr / samples / bluetooth / peripheral_ht / src /hts.c"
and I have enabled "CONFIG_TEMP_NRF5...
We are using nRF9160 DK (SDK 1.9.1) with "serial lte modem" firmware. We are trying to test downloading files from a server using AT commands to work with HTTP. The file is...
Upto a week I had *no* problem in programming a nRF52840 dongle with an app I am porting from the nRF52840dk.
All of a sudden I can't get the app running, the dongle appears...
I'm trying to get sprintf working with SDK 17.1. Basically, I'm struggling getting this simply use-case to work. char buf[32]; sprintf(buf, "%.3f", 3,5); I'm not able to find...
I know from zephyr samples that Tensorflow lite is available via zephyr as an external module, though it's not explicitly allowed in the nrf west.yml, and therefore is not...
Hi all, I follow example (serial) to build and run, i already run successfully, but i meet some question. when i use generic_on_off to control light at short time(2s), the...
Hi,
On a NRF52840, I try to perform `x` SPI transactions of 3 bytes each using EasyDMA Arraylist feature fully controlled by hardware. The CS must be toggled between each...
Dear Nordic Experts, The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832. When provisioning, it sometimes...
Hello, All
I am trying the scan_adv example, and use my phone to scan the advertising packet, unlike other peripheral examples, I found that it appears multiple time with...
ncs v1.9.1
Reference nrf\applications\serial_lte_modem\src\twi
This example does not see how to configure the pin.so how to config SCK and SDA Pin?
Thanks!!!
Is it feasible for me to use the 9160 as ble-host and 52820 as ble-controller using just TX and RX lines? (no request or ready lines) My setup is NCS v1.7.0, custom board...
I see that there is definitely support for where a user would cancel the USB host's request to suspend inside of app_usbd.c here's line 1246:
You can clearly see that it...
Hi,
I know that a GPS receiver can can use the Doppler effect to get an accurate velocity measurement. More accurate than the accuracy for position.
However, from my tests...
Hi,
I'm facing the mqtt error shown in the image below "E: mqtt_connect, error; -111" when I try to establish connection between the nRF9160 DK and AWS Cloud. I've double...
