Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
Hello,
I am trying to perform full modem FOTA update on my nRF9160 DK board using sample code without using buttons press functionality as we want to integrate the same...
Hi,
We are developing a product (to be produced in small quantities only) that included USB data transfer based on your USB CDC ACM module. We do not have our own USB vendor...
Can an iBasis sim card be activated without being in a device (nRF9160dk or Thingy:91).
I have two sim cards and neither will activate.
Most of the time after entering...
aoa rx hardware: nrf52833DK
aoa tx hardware: my test nrf52833 board
my test nrf52833 board download "direction_finding_connectionless_tx", use " overlay-aoa.conf"
nrf52833DK...
We are currently in the process of looking into the Bluetooth certification as part of a Homekit accessory, and the documentation raised some questions:
the QDID for the...
Hi,
I'm new to ble.
In order to better understand what is going on, on a packet leveI got a packet sniffer.
I found a device that uses a nordic chip, and am trying...
Hi, I am trying to develop an nCS application with serial flash interface, I am using an nRF52833dk & I observed that under the nCS path "v1.8.0\zephyr\drivers\flash" There...
Please guide what changes are to be done for the Light bulb example to be run in 52840 Dongle?
I am using VS Code and built the Build Configuration using the Dongle configuration...
Hello.
I am yoo at korea.
We will connect OLED with QSPI and Driver IC supports SLOWREAD.
- 8bit (Opcode: 0x03) + 24bit (Addr) + 8bit (Read value: Mandatory) + 8bit...
Hello.
I have question for QSPI OPCODE.
According to "nRF52840_PS_V1.5", WREN optional at "the custom Instruction".
- using function: nrf_drv_qspi_cinstr_xfer
...
Hi, I'm trying to use light_lightness example , and button_event_handler didn't work.
Error message is
"multiple definition of "GPIOTE_IRQHandler" "
because I added...
Hi, I'm using nRF52 DK. I'm following tutorial links 1 , 2 and 3 to learn how to add BLE OTA DFU to the example project ble_app_uart.
Step 1
Following the above links...
Dear ,
I am currently testing the UART peripheral on nRF52832 and nRF52840 using nRF Connect SDK.
Basically, I have a sensor that continues sending out data via uart and...
I'm trying to build the pc-ble-driver ( https://github.com/NordicSemiconductor/pc-ble-driver ) to be able to use the nRF52840 as a receiver for a thermometer. See https:/...
