Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hi
I am trying to setup a raspberry pi 4 for flashing nrf devices. But Nrfjprog doesn't seem to work.
I am using a Raspberry Pi 4 with 2021-05-07-raspios-buster-armhf...
Hi,
I noticed that the nRF9160s I2C low level logic voltage is quite high. With a 2kR resistor at 3.3V it's already more than 200mV. Because this is quite high and will...
Hello all,
I am using the BLE app UART code. I m trying to connect one plus through BLE connection. but nordic devkit BLE is not visible.
I am using the default configuration...
Sorry but I find the documentation useless. I don't even know where to start. It could be I have not found the correct documentation which is not surprising.
The best I...
Hi
I've built a USB HCI fimrware based on the sample from the nRF Connect SDK for the nRF52840DK.
See also: (+) HCI USB based on nRF Connect SDK 1.7.0 failed to update...
The SDK version of the program I developed with SES is v1.5.0. Now change the development environment to vscode and import the program into vscode through "add an existing...
Hi,
Is it possible to generate a passkey before initiating the pairing process?
The peripheral in my system does not have a display or input, so I'm looking for a way...
Hello Developers, I am currently developing an application on top of mqtt-sn publisher example. Now i want to add OTA DFU in my mqtt-sn based application. I have started up...
Hi, dk:PCA10095 sdk:ncs v1.7.0 example:path:D:\ncs\v1.7.0\peter\11_hello_world_pdm_i2s
Download changes when I build the project using SES: Previously: Download code available...
We used the nRF52840 in some projects, but there are still some problems with the short bridge at the IC during production.
So we want to leave the blank layout of the unused...
HI
We have to try to develop a product with nrf5340. The product needs to be waterproof and also it made up of metal and a small amount of plastic enclosure. In that how...
Dear Members,
I want to run ANT+ code in my custom board,
It works well on PCA10056, I can upload softdevice and the code to custom board board,
but I didn't get any...
I've recently upgraded my SDK to 1.6.0 and I am now unable to read the state of P1.00 but I am able to read the state of P0.28.
I've stripped the project down to just a...
I recently installed nRF Connect SDK using the Toolchain manager. Install went through without any issue but when I am trying to open an example project in SEGGER Embedded...
