Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
I'm trying to build my project for nRF54L15 DK. The project uses mcuboot. When mcuboot is being built, I get following warning:
I guess the problem is caused by the config...
Hi, DevZone,
Our customer, Hosiden Osaka, wants to get the recommened foot print regarding nRF54L15, that is, the following each land pattern respectively;
- WLCSP 300um...
I am writing a program for the nRF52805 for use in a battery-operated remote. It needs to wake up from sleep when any button is pressed, perform the interrupt (blinking an...
I have found that in NCS SDK 2.6.2 it was very simple to enable FLASH_SIMULATOR as part of the mcuboot configuration overlays. But starting from SDK 2.7.0, I keep getting...
Hello.
I found this in the sx126x .c driver :
These lines did not allow adding more than one device to the overlay . I removed this code and rewrote all driver files...
example Matter_light_switch in vs code
version using nrf connect sdk -> v2.8.0
manage tool-chain version v2.8.0
nrf52840dk
getting error while building code
...
Hi,
I follow the execise https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-8-bootloaders-and-dfu-fota/topic/device-firmware-update-dfu-essentials...
Hi,
I'm trying to find the BOM referenced in the Hardware Design Guidelines for the nRF9151 under the Schematic Design section. According to the document, the BOM should...
Is there a way to obtain the Tx/Rx packets num in LE Audio? I want to calculate the PER in LE Audio. Using nrf v2.60, NRF 5340 Audio DK.
Thanks for your reply.
When configuration options CONFIG_SEGGER_SYSTEMVIEW =y and CONFIG_TRACING =y are added to my prj.conf the following build errors are shown:
followed by many other errors...
Hi,
I have a NRF52840 DK , I was using it for development. After one day the board don't turn ON anymore. I'm using USB cable as a power source. Acording to several subject...
Hi:
I use ncs v2.8.0, using external flash(w25q128).
this is test flash project.
And this log:
Device_is_read returns a failure. But flash read/write successful...
I'm encountering an issue with the use of the GPIO interrupt type GPIO_INT_EDGE_BOTH on a GPIO connected to a button. When pressed, the button pulls the GPIO to GND, and when...
Hi there,
I am new to the platform , we are working on a proof of concept to reduce idle power consumption as low as possible on an NRF9160, I want to put the system in...
Hey,
We have a library (rust) responcible for communicating with the BLE peripheral Using btmgmt dbus messages to bluez.
We have never initiated a dedicated `aagent` in...
