Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
SDK: 15.3.0 Example: ble_app_multirole_lesc Device: EYSHJNZWZ (nRF52832)
I define the following macros in "Section Placement Macros".
Can I use these macro values in my...
When the boot loader calls the sd_mbr_command it does not get updated.
sd_mbr_command_t sd_mbr_cmd;
sd_mbr_cmd.command = SD_MBR_COMMAND_COPY_BL;
sd_mbr_cmd.params...
SDK: 15.3.0 Example: ble_app_multirole_lesc Device: EYSHJNZWZ (nRF52832)
I recognize by default that the top address of the app is 0x26000. I want to change the top address...
I need to measure current of loads attached to NRF52832 using current transformer(CT).
I can use SAADC library to read ADC value. But to measure current I have to know the...
I have a question about PeerManager.
SDK: 15.3.0 example: ble_app_multirole_lesc (I changed the source from the sample) deviceA: EYSHJNZWZ (nRF52832) deviceB: Android (ver9...
Dear All,
We would like to automate the trst procedure of our device in LabWiew because in this tool we are doing also electrical measurements.
We have tried nRF connect...
Hello,
I'm running custom firmware on a nRF52840 based DK (Rigado BMD-340).
The log from the nRF Connect app is as follows:
Could anyone help explain the error...
Hi,
I am using nrf mesh sdk v3.2.0 and I would like to combine our custom service within the mesh server example (includes the proxy service). Using info from other threads...
We are having issues with UART communication on the nRF52840. Using a logic analyzer, we have found that the transitions happen too quickly. This causes the receiving MCU...
I have been working with Thingy:91 for three weeks now. Everything works nicely, however, I could not get any GPS location from it. I am using Rogers simcard which is a local...
Hello everyone. My project is getting quite complex so I will try to abridge. (Mesh SDK 3.2.0) I am trying to send wifi credentials from an android application (derived from...
Hi guys,
here in Croatia I'm trying to connect to NB-IOT network using nrf9160.
Here are the commands i am executing:
After this command modem does not accept any...
hi all,
i build project use HCI controller with nrf52840 , it some time show error message,
how to deal with this issue
HCI Host Not enough space in buffer #hci
https...
Hi,
I am working on a development where the values of a bunch of nodes with a sensor needs to be captured in one aggregator device in a mesh network. The aggregator then...
